3onedata IGW1114 Series Quick Installation Manual - Page 3
Browse online or download pdf Quick Installation Manual for Gateway 3onedata IGW1114 Series. 3onedata IGW1114 Series 4 pages. Industrial modbus gateway
Also for 3onedata IGW1114 Series: Quick Installation Manual (4 pages)
Print Page
RS-232/485/422 3IN1 serial port, DB9M interface +
5-pin terminal blocks
Model I provides 1 3IN1 serial port, supports RS-232, RS-485
or
RS-422
(optional),
RS-232
adopts
RS-485/422 adopts 5-pin 5.08mm pitch terminal blocks. The
pin definitions are as shown in the following table:
PIN
RS-232
PIN
RS-485
1
DCD
1
D+
2
RXD
2
D-
3
TXD
3
GND
4
DTR
4
—
5
GND
5
—
6
DSR
7
RTS
8
CTS
9
—
RS-232/485/422 3IN1 serial port(DB9M)
The Model II and Model III provide 3IN1
serial port, which supports RS-232, RS-485
or RS-422 (optional). The interface type is
DB9 male and its pin definitions are as follows:
PIN
RS-232
RS-422
1
DCD
T+
2
RXD
T-
3
TXD
R+
4
DTR
R-
5
GND
GND
6
DSR
-
7
RTS
-
8
CTS
-
9
-
-
【Checking LED Indicator】
The LED indicators on the front panel of this series device
monitor the device working status, which has simplified the
overall troubleshooting process. the function of each LED is
DB9
female,
described in the table as below:
LED
P1-P2
RS-422
T+
T-
RUN
GND
R+
R-
LINK (1-2)
TX (1/-4)
RS-485
RX (1/-4)
D+
D-
【Logging in to WEB Interface】
-
This device supports WEB management and configuration.
-
Computer can access the device LAN1 via Ethernet interface.
GND
The way of logging in to device's configuration interface via IE
-
browser is shown as below:
-
Step 1
Configure the IP addresses of computer and the
-
device to the same network segment, and the
network between them can be mutually accessed
-
Indicate
Description
PWR is connected and running
ON
normally
PWR is disconnected or running
OFF
abnormally
The system is running normally
Blinking
The system is not running or
OFF
running abnormally
The system is running
ON
abnormally
LAN port has established valid
ON
network connection
LAN port is in an active network
Blinking
status
LAN port hasn't established valid
OFF
network connection
Serial port is not transmitting
OFF
data or transmitting data
abnormally
Serial port is transmitting data.
Blinking
Serial port is not receiving data
OFF
or receiving data abnormally
Serial port is receiving data.
Blinking
Step 2
Enter device's IP address in the address bar of the
computer browser.
Step 3
Enter device's username and password in the login
window as shown below.
Step 4
Click "Login" button to login to the WEB interface of
the device.
Note:
In the Dual IP mode, the default IP address of LAN1 is
"192.168.1.254", the default IP address of LAN2 is
"192.168.8.254".
The default user name and password of the device are
"admin".
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel