AirVerter AV-096 User Manual - Page 3

Browse online or download pdf User Manual for Paint Sprayer AirVerter AV-096. AirVerter AV-096 12 pages. Hvlp paint spray system

Print Page

Air Compressor

A. Air compressors used with AirVerter

Guns must be able to HOLD a minimum of 40

PSI while spraying. Note: Position a

pressure gauge in the air hose nearest the

spray gun to be assured of the PSI required to

satisfactorily spray your coating.

B. The AirVerter

Inductor (AV-005) requires a

minimum 5 HP compressor.

A. The Model AV-096 Spray Gun operates with a

constant flow of air through the gun.

trigger controls the fluid flow only. The Model

96 Spray Gun requires an AirVerter

Assembly

between

compressed air supply.

B. Consult the Needle, Nozzle and Air Cap

Selection Guide to select the proper

combination for the coating and finish

quality desired.

create unnecessary overspray!

Using a One-Quart Paint Cup

A. Attach the 1-Quart Paint Cup (AV-188) to the

Fluid Tube Fitting (AV-9604) on the bottom of

the gun and tighten. Attach the Air Pressure

Tube on the cup lid to the Air Pressure Elbow

(AV-176) on the gun.

B. The 1-Quart Paint Cup must be airtight, clean

and free of obstructions.

• The seal between the paint cup lid gasket

and the lip of the cup MUST BE airtight.

• The Air Pressure Tube supplying air to the

paint cup MUST BE clean and free of

obstructions.

C. Never fill a 1-Quart Paint Cup more than ¾

full. This allows sufficient air space in the cup

for pressurization.

020) will reduce clean-up time and solvent

usage.

D. Attach an Inductor Assembly (AV-005) to the

male quick-disconnect at the base of the gun

handle.

DO NOT OPERATE SPRAY GUNS WITHOUT PERSONAL SAFETY EQUIPMENT

AirVerter

Model 96 HVLP Paint Spray System

EQUIPMENT REQUIREMENTS

Spray

OPERATING INSTRUCTIONS

Inductor

the

gun

and

Too much pressure will

Using a Cup Liner (AV-

High Pressure Air Hose

A. Air hose lengths up to 50 feet MUST have an

I.D. of 3/8" including fittings.

B. Air hose lengths greater than 50 feet MUST

have an I.D. of 1/2" including fittings.

Paint Cup, Pressure Pot or

Diaphragm Pump

Be certain to follow manufacturer's instructions.

Using a Two-Quart or Larger

The

Remote Pressure Pot

or Diaphragm Pump

the

A. Remove the Air Pressure Elbow (AV-176) and

replace it with the Air Pressure Plug (AV-177)

found in your parts kit.

B. Attach the fluid hose from your pressure pot to

the Fluid Tube Fitting (AV-9604) on the gun

and tighten.

C. Attach an Inductor Assembly (AV-005) to the

Male Quick Disconnect (AV-172) at the base

of the gun handle.

the

Guidelines listed on the following page.

B. Before paint is poured into the cup or

diaphragm pump, make certain paint is

properly mixed. This is particularly true when

mixing multi-component paints.

shaker, rotary mixer, or paint paddle to achieve

a homogeneous mixture. (Hint: Split your paint

into two parts; the top will be lighter and the

bottom will be heavier.

bottom half of the paint and slowly add small

amounts of the top half into the heavier

bottom.)

C. Strain your paint to remove impurities. Use

a cone strainer or a 100-mesh nylon bag or

equivalent strainer.

D. Thin

your

manufacturer's specifications.

Before Spraying

Air

and

Paint

Completely stir the

paint

according

Management

Use a paint

the