DANLERS CBU-HBSP IP66 BK Installation

Browse online or download pdf Installation for Security Sensors DANLERS CBU-HBSP IP66 BK. DANLERS CBU-HBSP IP66 BK 2 pages. Rated ceiling high bay (spot) passive infra red (pir) occupancy detector & photocell

Print Page

CBU-HBSP IP66

IP66 Rated Ceiling High Bay (Spot) Passive

Infra Red (PIR) Occupancy Detector & Photocell

Input: 100-240 Vac 50/60Hz

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT

NOTE: CBU-HBSP IP66 is only compatible to work with CASAMBI enable equipment

This CBU-HBSP IP66 High Bay

(Spot Detection) Lighting Control

has an IP66 rated weatherproof

enclosure and can be ceiling

mounted. Conﬁ gurable via the free

to download Casambi APP on

Google Play or Apple APP Store.

INSTALLATION

To be installed by a competent person with

reference to BS 7671 or equivalent local standards.

If in doubt consult a qualiﬁ ed electrician.

• Plan where the CBU-HBSP IP66 is to be located

(see diagram 1). Switch off supply and check for

hidden cables and pipes.

• Remove the front cover by quarter turning the

four quick release fasteners to the '0' position

(see diagram 4 overleaf).

• Mount the back section of the mounting box in

the required location via the 4 corner holes.

• Thread mains cable carefully through the

required membrane entry point.

• Unclip the internal back plate. Remove the

required knock out if replacing the optional

internal back plate.

• Thread mains cable into the unit. The CBU-

HBSP IP66 should be connected as shown in

diagram 2:

L - Live in. N - Neutral in.

• Reclip the internal back plate if required.

• Replace the front cover ensuring the quick

release fasteners are secured in the '1' position.

OPERATION

To check the operation of the CBU-HBSP IP66:

• Turn on the supply then after 20 seconds if the

sensor has recognised movement of a person

within its zone of detection the integral red LED

on CBU-HBSP IP66 will stay illuminated for 4

seconds before the red LED turns off.

• Thereafter, every time movement is detected by

CBU-HBSP IP66 the integral red LED will stay

illuminated for 4 seconds.

The control also features adjustable time out (time

lag) control and daylight threshold control which

are conﬁ gured by the Casambi APP.

PRECAUTIONS

• Do not place the CBU-HBSP IP66 near heat

sources, fans or in ventilated ceiling voids.

• CBU-HBSP IP66 can be wired in parallel

(sharing the same Live and Neutral).

• Do not place close to, or positioned such

that, any light source points directly into the

CBU-HBSP IP66.

• Ensure wires and cables are securely held within

the connection terminals.

• The CBU-HBSP IP66 should be protected by a

5 or 6 Ampere mcb or fuse.

• Disconnect the CBU-HBSP IP66 from the

circuit before performing insulation testing

of the wiring circuit.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388 E-mail: [email protected]

www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

07/06/19

TECHNICAL DETAILS

INPUT

Voltage:

100 - 240Vac

Frequency:

50/60Hz

Max. mains current:

20mA

Standby current:

14mA

RADIO TRANSCEIVER

Operating frequencies:

2.4... 2,483 GHz

Max. output power:

+4 dBm

LUX PARAMETERS

Mounting height up to 12m

Range:

5 - 2000 lux

Perspective view - ceiling mounted

OPERATING CONDITIONS

Note: The temperature difference between the

detection target and the background must be at

least 4 °C.

-20... +40 °C (lout

Ambient temperature:

20mA)

Storage temperature:

-25... +75 °C

Max. relative humidity:

0... 80%, non cond.

CONNECTORS

Terminal block

0.5mm

Wire size:

or stranded

Wire strip length:

6-7mm

Tightening torque:

0,4 Nm/4 Kgf.cm

MECHANICAL DATA

110mm x 110mm x

Dimensions:

73mm

Weight:

255g (unpacked)

Degree of protection:

IP66

Up to 3m

Protection class:

Built-in Class 2

Flame-retardant

Material (casing)

polycarbonate/

Polypropylene.

Finish / Colour:

Matt /Grey

WM-HBSP IP66 GR

(RAL 7035)

Finish / Colour:

White

WM-HBSP IP66 WH

(RAL 9001)

Finish / Colour:

Black

WM-HBSP IP66 BL

(RAL 9005)

Protection class:

Built-in Class 2

CONFORMITY AND STANDARDS

EMC emission:

EN 301 489-1 V2.2.0, EN 301 489-17 V3.1.1,

EN 55032: 2015, EN61000-3-2: 2014,

EN61000-3-3: 2013

EMC immunity:

EN 301 489-1 V2.2.0, EN 301 489-17 V3.1.1

Environment:

Complies with WEEE and RoHS directives

CB scheme:

IEC60669-1:1998, IEC60669-1:1998/AMD1:1999,

IEC60669-1:1998/AMD2:2006, IEC60669-2:2002,

IEC60669-2-1:2002/AMD1:2008,

COLOUR OPTIONS

This product is available in 3 colour options

designated by the following product codes:

Grey:

CBU-HBSP IP66 GY

White:

CBU-HBSP IP66 WH

Black:

CBU-HBSP IP66 BK

5 YEAR WARRANTY

CBU-HBSP IP66 (XX) comes with

a 5 year warranty from the date of

manufacture and is CE marked.

Mounting height up to 20m

Perspective view - ceiling mounted

- 2.5mm

solid

15m

Suggested typical wiring

230 Vac

5A or 6A MCB

or fuse

L - Live in. N - Neutral in.

Two neutral and two live terminals

are available for easy 'loop in' and

'loop out' connection.

Up to 5m diameter

DIAGRAM 1

DIAGRAM 2

plan

side

110

DIAGRAM 3

INS370 CBU-HBSP IP66 (Issue 02)