Automationdirect.com SOLO SL4896-RRE Quick Start Guid - Page 2

Browse online or download pdf Quick Start Guid for Temperature Controller Automationdirect.com SOLO SL4896-RRE. Automationdirect.com SOLO SL4896-RRE 4 pages.

Print Page

Automationdirect.com SOLO SL4896-RRE Quick Start Guid

Mounting Instructions

SOLO temperature controllers can be mounted through a cutout in an enclosure or panel by using the dimen-

sions shown in Section 5. The directions for mounting the controller through a cutout are:

1. Insert the temperature controller through the panel cutout.

2. Slide the M3X0.5 nut into the opening in the top of the mounting bracket and insert the M3X0.5 X 30mm

mounting screw in the mounting bracket.

3. Insert the mounting bracket into the mounting groove at the top and bottom of the controller, and push the

mounting bracket forward until the bracket stops.

4. Tighten top and bottom screws evenly to secure temperature controller in place.

Terminal Identification

WARNING! Electric shock danger

To prevent electric shock, do not connect AC power to your device until all input and output

connections are completed.

SL4896-RRE

SL4896-CRE

Sensor Input

0 – 10 VDC

4 – 20 mA

2-wire RTD

Thermocouple

3-wire RTD

All manuals and user guides at all-guides.com

SL4896-VRE

SL4896-LRE

Power Input

AC Powered

Models

DC Powered

Models

24 VDC power for models with

–D suffix only

Display, LED and Key Pad

PV Display: To display the process value or parameter type.

SOLO

SV Display: To display the set point, parameter operation read value

4896

manipulated variable or set value of the parameter.

AT: Auto-tuning LED, flashes when the Auto-tuning operation is ON.

OUT1 / OUT2: Output LED, lights when the output is ON.

ALM1 / ALM2 / ALM3: Alarm output LED, lights when that alarm is on.

°C, °F: Temperature unit LED. °C: Celsius °F: Fahrenheit

OUT1

OUT2

Set Button: Press this key to select the desired function mode and

confirm the setting value.

ALM1

ALM2 ALM3

Rotate Button: Press this key to select parameters within the function

mode.

SET

Down Button: Press this key to decrease values displayed on the SV

display. Hold down this key to speed up the decrement.

Up Button: Press this key to increase values displayed on the SV

display. Hold down this key to speed up the increment.

Key Pad Operation

SET

Press for less

than 3 sec.

Regulation

Operation Mode

Mode

SET

Regulation

Parameters

The SOLO temperature controller has three function modes: Initial Setting mode, Operation mode and Regulation

mode. When power is first applied to the temperature controller, the module information splash screen appears.

This screen shows the firmware version on the PV display and the two output types for that particular model on

the SV display. After three seconds, the controller will automatically proceed to the Operation mode main screen.

Press and hold the

;

button for three seconds to go into the Initial Setting mode. Press the

than three seconds to access the Regulation mode. Press the

modes to access the individual parameters for each function mode. Use the

individual parameter values. Pressing the

;

button saves the parameter values. Press the

to return the controller to the Operation mode.

Reset to Factory Default Instructions

All of the following set up instructions are for setting up a controller from the factory defaults. If the

application for a controller needs to be changed, reset the controller to factory default using the following

steps.

1. Press the

•

button until the parameter

loC

;

button.

2. Press and hold the

and

buttons simultaneously for one second and release.

3. Press the

•

button repeatedly until the PV display shows

on the SV display to

1357

. Press the

;

button.

4. Cycle power on the Controller to reset to factory default mode. All user set values are erased.

11-1

Thermocouple or RTD Input

1. Access the Initial Setup mode by pressing and holding the

inpt

, use the

and

buttons to select the value that corresponds to the thermocouple or RTD type

that will be attached to the controller. See the table below for specifications. Press the

selected value. The controller will display the module information splash screen for three seconds and then

return to the main screen.

2. Press the

;

button for three seconds again. Press the

the

and

buttons to select either

for Centigrade or

to save the selected value. The controller will display the module information splash screen for three seconds

and then return to the main screen.

3. Press the

;

button for three seconds again. Press the

appears. Use the

and

buttons to set the maximum value of the operational temperature range. In

operation, if the PV value is higher than the TP-H value, the PV display flashes to indicate an error and the

controller outputs shut off. The SV value cannot exceed the TP-H value. Press the

selected value. Press the

•

button to access the

the minimum value of the operational temperature range. In operation, if the PV value is lower than the TP-L

value, the PV display flashes to indicate an error and the controller outputs shut off. The SV value cannot be set

lower than the TP-L value. Press the

;

button twice to save the selected value and return to the controller

main screen.

4. Press the

•

button repeatedly until the parameter

either

for a whole degree or

for a tenth degree temperature display.* Press the

the selected value and return to the controller main screen.

5. If the input temperature from the thermocouple or RTD needs to be adjusted, press the

than 3 seconds. Press the

•

button repeatedly until the parameter

buttons to adjust a positive or negative offset to the PV value displayed on the controller. Press the

twice to save the selected value and return to the controller main screen.

*Note: The decimal point display cannot be adjusted for B, S, and R type thermocouples.

Thermocouple* Type and Temperature Range

Input Temperature Sensor Type

Thermocouple TXK type

Thermocouple U type

Thermocouple L type

Thermocouple B type

Thermocouple S type

Thermocouple R type

Thermocouple N type

Thermocouple E type

Thermocouple T type

Thermocouple J type

Thermocouple K type

RTD Type and Temperature Range

Input Temperature Sensor Type

Platinum Resistance (Pt100)

Platinum Resistance (JPt100)

*Note: Use only ungrounded thermocouples.

SET

Hold for 3 sec.

Initial Setting

Mode

SET

Operation

Initial Setting

Parameters

;

button for less

•

button while inside any of the three function

and

buttons to change the

;

button again

appears. Use the

button to select

loC1

. Press the

pass

. Use the

button to change the value

;

button for three seconds. In the parameter

;

button to save the

•

button to access the

tpun

parameter. Use

for Fahrenheit display. Press the

;

•

button repeatedly until the

tp-H

;

button to save the

tp-l

parameter. Use the

and

buttons to set

appears. Use the

and

buttons to select

;

button twice to save

;

button for less

tpof

appears. Use the

;

LED Display

Temperature Range

-328 ~ 1472°F (-200 ~ 800°C)

txk

-328 ~ 932°F (-200 ~ 500°C)

-328 ~ 1562°F (-200 ~ 850°C)

-212 ~ 3272°F (100 ~ 1800°C)

32 ~ 3092°F (0 ~ 1700°C)

-328 ~ 2372°F (-200 ~ 1300°C)

32 ~ 1112°F (0 ~ 600°C)

-328 ~ 752°F (-200 ~ 400°C)

-148 ~ 2192°F (-100 ~ 1200°C)

-328 ~ 2372°F (-200 ~ 1300°C)

LED Display

Temperature Range

-328 ~ 1112°F (-200 ~ 600°C)

-4 ~ 752°F (-20 ~ 400°C)

jpt

button

parameter

and

button