Indesit ID6IVS2/UK Operating Instructions Manual - Page 3
Browse online or download pdf Operating Instructions Manual for Cookers Indesit ID6IVS2/UK. Indesit ID6IVS2/UK 28 pages. Free standing electric cooker
Print Page
Installation
WARNING - THIS APPLIANCE MUST BE EARTHED.
Mains Connection
Your cooker should have been checked to ensure that
the voltage corresponds with your supply voltage, this is
stated on the rating plate, which is situated on the outer
rear panel.The model number and the serial number
are located on the front of the cooker, as shown on the
Features page.
The cooker must be connected by a competent person
such as one who is a, NICEIC registered contractor
to a suitable double-pole control unit with a minimum
rating of 32A and a minimum contact clearance of 3mm
(applicable to newer properties, older properties where
a 30A double pole control unit and a minimum contact
clearance of 3mm is acceptable).
The double pole control unit should be fitted adjacent
to the cooker, in accordance with IEE regulations.The
control unit must be within 2 metres of but not directly
above the appliance and should be easily accessible in
the event of an emergency.
The power supply cable should conform to B.S.6004 with
a conductor size of 6mm
, minimum.
2
Access to the mains terminals is gained by removing the
rear access cover. The mains cable must pass through
the cable clamp adjacent to the terminal block. Sufficient
cable should be used to allow the cooker to be pulled
out for servicing.
Ensure that the mains cable is routed away from any
brackets affixed to the rear panel and is not trapped
to the rear wall when pushing the cooker into position
between cabinets.
For the installation of the feeding cable carry out the
following operations:
1
Open the terminal
b o a r d b y i n s e r t i n g
a screwdriver into the
bottom tabs of the cover.
Use the screwdriver as a
lever by pushing it down
to open the cover (see
diagram).
2
Loosen the cable
clamp screw and remove
it, using a screwdriver as
a lever (see figure).
3 . F a s t e n t h e w i r e s
under the screw heads,
respecting
t h e c o l o u r c o d e :
Black/Blue (N), Red/
Brown (L) and Bare Wire/
Yellow-Green (
).
Once the connections have been made, tighten all the
terminal screws fully.
Fasten the supply cable in place with the clamp and
close the cover of the terminal board.
Levelling
Four feet are fitted which can be adjusted up or down to
set the height (900mm - 930mm) and level the cooker.
The feet can be simply screwed in or out to lower or raise
the cooker.
After the correct height is achieved, lock the feet into
position by tightening the locking nut using an open
ended spanner.
CAUTION: Some soft floor coverings may get damaged
if the cooker is not moved carefully.
NOTE: Ensure oven shelves are level by using a spirit
level on the rod shelves.
Siting the Cooker
The cooker is designed to fit between kitchen cabinets
spaced 600mm apart.
The space either side need only be sufficient to allow
withdrawal of the cooker for servicing and cleaning. It
can be used with cabinets one side or both as well as in
an angled corner setting.
It can also be used freestanding.
Adjacent side walls which project above hob level, must
not be nearer to the cooker than 150mm and should be
protected by heat resistant material. Any overhanging
surface or cooker hood should not be nearer than 650mm.
Note: This appliance must NOT be fitted on a platform.
Moving the Cooker
Note: Take care in moving the cooker as it is heavy.
Take care to ensure that any floor covering is not
damaged.
Radio Interference
This appliance conforms to EN 55014 regarding
suppression of radio and television interference.
Before moving your
cooker, switch off at
the cooker control unit,
ensure that it is cool.
Open the grill door
sufficiently to allow a
comfortable grip on the
underside front edge of
the oven roof, avoiding
any grill elements.
3
GB