Pioneer CLD-901 Operating Instructions Manual - Page 34

Browse online or download pdf Operating Instructions Manual for CD Player Pioneer CLD-901. Pioneer CLD-901 40 pages. Compact disc/laservision player
Also for Pioneer CLD-901: Operating Instructions Manual (40 pages)

Print Page

TROUBLESHOOTING

Before concluding that the player is out of order, please refer to this troubleshooting guide to make sure that there

is not a simple remedy for the problem.

The vast majority of performance problems have their source in set up

Find the

errors, bad connections to other equipment, or malfunctions of other equipment (TV, stereo system}.

trouble symptom

on the chart below, and try the suggested remedies.

SYMPTOM

CAUSE

e@ Power cord is not properly plugged into AC

wall socket.

@ Power switch is not turned on.

Disc table is not expelled

when EJECT button is pressed.

REMEDY

@ Plug in power cord.

@ Turn on power switch.

Automatic start not

functioning.

e@ Other equipment connected to |/O port on rear.

Disc table is expelled after

PLAY indicator blinks for

approx. 10 seconds.

@ Disc is warped or dirty.

@ Moisture has condensed on parts in the player.

Player stops part way through

playback, and disc table opens.

® Automatic start function cannot be used when

controlling through I/O port.

e Refer to instructions under Remedy",

item 11,

and correct or clean disc.

@ Remove disc and let player stand for 1 to 2 hours

until it is dry.

TV no longer receives other

e@ Antenna cable has not been connected.

channels after it has been

connected to the player.

e LVP indicator is lit, and player is in LVP mode.

——CxX

SYSTEM

s—_ =

ax —

e@ Connect VHF antenna cable to antenna terminal

on the player.

@Press the TV/LVP key on the remote contro!

unit to turn the indicator off, or turn off the

player's power switch.

SYSTEM

Slanting stripes appear on the

TV screen when TV/LVP key

is pressed to receive TV

broadcasts.

@ Electric field for TV broadcasting is weak.

(This does not indicate any trouble.)

@ Remote control unit batteries are weak.

@ There is an obstacle between the player and

the remote control unit.

e Remote control unit is not in a good location for

transmission.

@ Other equipment is connected to {/O port on rear

panel, or a plug is inserted in CONTROL

terminal.

Remote contro! does not

work.

®@ Some TV sets have remote control functions that

operate improperly in response to the remote

control unit of the player.

Operation of the remote

control! unit causes the TV to

operate improperly.

WHEN

A LASERVISION

DISC

IS BEING

PLAYED

SYMPTOM

Disc rotates but there is no

picture.

e The TV set is not turned on.

Wrong connections from player to TV.

@ TV set is not turned to channel 3 or 4:

e Player VHF CHANNEL SELECTOR

is at the

wrong setting.

@ Piayer is in the PAUSE mode.

e@ LVP indicator is not lit.

@ Turn off the power switch of the player.

We recommend that you turn off the power

switch of the player, whenever you intend to

watch TV for a long time.

e Replace batteries.

e@ Remove the obstacle or shift the remote control

position.

e Operate the remote control unit in front of the

player.

@ Commands from remote control not accepted

when I/O port or CONTROL

IN terminal are in

use.

@ Move the TV and the player further apart, or

cover the remote sensor of the TV during disc

playback.

REMEDY

e Turn on TV,

e@ Make correct connections.

e@ Set TV to the channel (3 or 4) that is not used

for TV broadcasting in your area.

@ Set selector to same channel as the TV's empty

channel.

e Press the PLAY key.

@ Press the TV/LVP key on the remote control

unit so that the LVP indicator turns on.

SEER

PASS

CEE