Whirlpool AWO/C 0714 Instructions For Use Manual - Page 13
Browse online or download pdf Instructions For Use Manual for Washer Whirlpool AWO/C 0714. Whirlpool AWO/C 0714 14 pages. 7kg, 1400rpm, 6th sense washing machine with clean +, white wwdc 7410
Also for Whirlpool AWO/C 0714: Instructions For Use Manual (14 pages), Programme Chart (2 pages)
Print Page
INSTALLATION GUIDE
Pictures are on the cover of this Instruction for Use
Noise, excessive vibrations and water leakages
can be caused by incorrect installation of washing
machine.
If your washing machine is NOT a built-in model
NEVER move the appliance by carrying it at the
worktop.
REMOVE TRANSPORT BOLTS! (pict.1)
Important:
- Not removed transport bolts cause damages
to the appliance!
- Keep the transport bolts for further
transporting of the appliance; in this case
refit the transport bolts in reverse order.
1. Loosen the screws of all 4 transport bolts by
about 35 mm (pict. 2a).
2. Push screw inside of machine to stop position
(min. 20 mm) (pict. 2b).
3. Pull out the rubber rings from the holes (do not
pull the screws!). The whole transport bolt can
be removed now (pict. 2c).
4. Push the plastic caps delivered with your
washing machine on the holes to close them
(pict. 2d).
ADJUSTMENT OF THE FEET
The appliance must be installed on a solid and level
floor surface (if necessary use a spirit level).
If the appliance is to be installed on a wooden or
floating floor, distribute the weight by placing it on a
floating floor, distribute the weight by placing it on a
floating floor, distribute the weight by placing it on a
sheet of plywood measuring at least 60 x 60 cm and
sheet of plywood measuring at least 60 x 60 cm and
sheet of plywood measuring at least 60 x 60 cm and
thickness of at least 3 cm which is secured to the
thickness of at least 3 cm which is secured to the
thickness of at least 3 cm which is secured to the
floor. If the floor is uneven, adjust the 4 levelling feet
floor. If the floor is uneven, adjust the 4 levelling feet
floor. If the floor is uneven, adjust the 4 levelling feet
as required; do not insert pieces of wood etc. under
as required; do not insert pieces of wood etc. under
as required; do not insert pieces of wood etc. under
the feet.
Screw out the washing machine´s feet by hand with
Screw out the washing machine´s feet by hand with
Screw out the washing machine´s feet by hand with
2-3 clockwise turns and then slacken the locknut by
2-3 clockwise turns and then slacken the locknut by
2-3 clockwise turns and then slacken the locknut by
wrench (see pict. 3, 4).
Slightly lift the machine and adjust the height of the
Slightly lift the machine and adjust the height of the
Slightly lift the machine and adjust the height of the
foot revolving it (pict. 4).
4
4
Important: tighten the locknut by turning it anti-
tighten the locknut by turning it anti-
tighten the locknut by turning it anti-
clockwise towards the appliance casing (pict. 5, 6).
CONNECT THE WATER INLET HOSE
If the water inlet hose is not already installed, screw
by hand the bent end of the inlet hose to the valve on
the washing machine's back (pict. 7, 8).
Screw by hand the straight end of the inlet hose to
the tap, tightening the nut.
Attention:
• No kinks in the hose!
• The appliance must not be connected to the
mixing tap of an un-pressurized water heater.
• Check water-tightness of connections by turning
the tap completely on.
• If the hose is too short, replace it with a suitable
length of pressure resistant hose (1000 kPa min,
EN 50084 approved type).
).
).
If you need a longer waterstop hose, contact
our After Sales Service or your dealer.
• Check the inlet hose regularly for brittleness
and cracks and replace if necessary.
• The washing machine can be connected without
a backflow valve.
CONNECT THE DRAIN HOSE
1. In case the drain hose is installed as shown on
pict. 9: Unclip it from the holders marked with
arrows.
2. In case the drain hose is installed in the upper
part of the washing machine (pict. 10): Unclip it
from both holders marked with arrows
(depending on the model ).
3. Firmly connect the drain hose to the siphon, or
another outlet for drain water.
• Make sure there are no kinks in the drain hose.
• Secure the hose so that it cannot fall down.
Secure the hose s
Secure the hose s
• Small hand basins are not appropriate.
Small hand basins are not appropriate.
Small hand basins are not appropriate.
• To make an extension, use a hose of the same
o make an extension, use a hose of the same
o make an extension, use a hose of the same
type and secure the connections with clips.
type and secure t
type and secure
• Height for siphon - drain hose connection must
Height for siphon - drain hose connection must
Height for siphon - drain hose connection must
be minimum 60 cm and maximum 125 cm
be minimum 60 c
be minimum 60 c
• Max. Overall drain hose length: 2,50 m (in this
Max. Overall drain hose length: 2,50
Max. Overall drain hose length: 2,50
case, the maximu
case, the maximu
case, the maximum height for fixation is 90 cm).
ELECTRICAL CONNECTION
ELECTRICAL CONNECTION
ELECTRICAL CONNECTION
Use a socket with an earth connection.
•
Do not use extension leads or multi sockets.
•
The electrical power cable must be replaced
•
exclusively by a licensed electrician.
Electrical connections must be made in accordance
•
with local regulations.
GB 13
r drain water.
r drain water.
are no kinks in the drain hose.
are no kinks in the drain hose.
o that it cannot fall down.
o that it cannot fall down.
the connections with clips.
he connections with clips.