ACQUA SOURCE WPLD-5R351-SBB Installation Instruction - Page 2

Browse online or download pdf Installation Instruction for Swimming Pool Lighting ACQUA SOURCE WPLD-5R351-SBB. ACQUA SOURCE WPLD-5R351-SBB 2 pages. Wall mounted lamp

Print Page
INSTALLATION
1. Input voltage is AC12V. The lamps must be connected with transformer.
2. The junc�on box is located at least 1200mm from the edge of the pool.
DIMENSION
DIMENSION
INSTALLATION
INSTALLATION
Figure 1
3. The moun�ng bracket must be properly installed so that the top edge of the
1. Input voltage is AC12V. The lamps must be connected with transformer.
1. Input voltage is AC12V. The lamps must be connected with transformer.
light's lens is at least 450mm below the water level in the pool. see Figure 1.
2. The junc�on box is located at least 1200mm from the edge of the pool.
2. The junc�on box is located at least 1200mm from the edge of the pool.
4. Make sure the surface of pool wall is flat.
MINI 1200mm
Junc�on Box
Junc�on Box
Fix the bracket with 4pcs screws.
5. If the cable connec�on is done underwater, the connec�on part must be
Rigid conduit
waterproof protected (use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
3. The moun�ng bracket must be properly installed so that the top edge of the
3. The moun�ng bracket must be properly installed so that the top edge of the
light's lens is at least 450mm below the water level in the pool. see Figure 1.
light's lens is at least 450mm below the water level in the pool. see Figure 1.
MINI 1200mm
FIXTURE
MOUNTING
SCREW LOCATION
SCREW
Mini. from bo�om of
Mini. from bo�om of
J.B. to water level
J.B. to water level
TOP
Water Level
From water level to top of lens
From water level to top of lens
CONDUIT
7CM FROM
CENTER
FIXTURE TAB
SLOT
Wall surface
Wall surface
Rigid conduit
Pool body
Pool body
250mm
250mm
Figure 1
Figure 1
2
2
2
6. Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
8. There are 3 wires for RGB with remote control.
Connec�ng the signal wire out of water, enhancing the ability of signal receiving.
4. Make sure the surface of pool wall is flat.
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
Fix the bracket with 4pcs screws.
9. It is easy to replace the lamp.
5. If the cable connec�on is done underwater, the connec�on part must be
5. If the cable connec�on is done underwater, the connec�on part must be
waterproof protected (use waterproof cable gland or fill with epoxy glue).
waterproof protected (use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
Otherwise, the water will come in the lamp through the wires.
Open Posi�on
6. Connect all wires to the corresponding circuit wires in the junc�on box and
6. Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
feed epoxy.
RGB Working Mode
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
completely submerged in water.
Water Level
15 Color Programs(For RGB ON/OFF )
No.1
8. It is easy to replace the lamp.
No.2
8. It is easy to replace the lamp.
Blue
Red
No.5
No.6
Blue/Green
Red/Green
No.9
No.10
Grn-Grn/Blu-Blue
Red-Red/Blu-Blue
No.12
Same as program 11, the speed is slower.
No.14
Posición libre
Posición libre
Gradual change of all colors.
3
Signal wire
FIXTURE
FIXTURE
MOUNTING
MOUNTING
AC Power wire
SCREW LOCATION
SCREW LOCATION
SCREW
SCREW
TOP
TOP
AV power wire
CONDUIT
CONDUIT
7CM FROM
7CM FROM
CENTER
CENTER
FIXTURE TAB
FIXTURE TAB
SLOT
SLOT
Lock Posi�on
No.3
No.4
Green
Red/Blue
No.7
No.8
White
Red-Red/Grn-Grn
No.11
Cycle Red-Grn-Blu,Speed from fast to low.
No.13
Grn-Red/Blu-Blu-Red-White-Blu/Grn-Red/Grn
No.15
Posición bloqueada
Posición bloqueada
Gradual change of Red-Grn-Blu.
3
3