Canon PIXMA MX700 Series Servicehandleiding - Pagina 7

Blader online of download pdf Servicehandleiding voor {categorie_naam} Canon PIXMA MX700 Series. Canon PIXMA MX700 Series 44 pagina's. Office all-in-one printer
Ook voor Canon PIXMA MX700 Series: Schoonmaakhandleiding (7 pagina's), Handleiding voor netwerkinstellingen (32 pagina's), Aanvullende handleiding (6 pagina's), Installatie-instructies (2 pagina's), Brochure & specificaties (2 pagina's), Technische informatie (2 pagina's)

Canon PIXMA MX700 Series Servicehandleiding
The connected digital
camera or digital video
camera does not support
Camera Direct Printing.
The remaining ink
amount unknown.
Ink tank not recognized.
Ink tank not recognized.
Scanning unit (printer
cover) open.
Non-supported hub
No ink (no raw ink).
2-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is
displayed on the LCD.
Cycles of
blinking of
Alarm and
Power LEDs
2 times
Carriage error
3 times
Line feed error
4 times
Purge cam sensor error
[2001] The device may be incompatible.
Remove the device and check the
manual supplied with the connected
device.
[1683] (Applicable ink tank icon)
The remaining level of the following
ink cannot be correctly detected.
Replace the ink tank. (U130)
[1684] The following ink tank cannot be
recognized. (U140)
(Applicable ink tank icon)
[1410
The following ink tank cannot be
to
recognized. (U150)
1419]
(Applicable ink tank icon)
[1200] Cover is open. Close cover.
[2002] An unsupported USB hub is
connected. Remove the hub.
[1688] The following ink has run out.
Replace the ink tank. (U163)
(Applicable ink tank icon)
Error
Error
code
[5100] An error occurred in the carriage
[6000] An error occurred in the LF encoder
[5C00] An error occurred in the purge unit.
absorber is replaced.
Remove the cable between the camera and the
machine.
An ink tank which has once been empty is installed.
Replace the applicable ink tank with a new one.
Printing with a once-empty ink tank can damage the
machine.
To continue printing without replacing the ink tank(s),
press the Stop/Reset button for 5 sec. or longer to
disable the function to detect the remaining ink
amount. After the operation, it is recorded in the
machine EEPROM that the function to detect the
remaining ink amount was disabled.
A non-supported ink tank is installed (the ink tank
LED is turned off). Install the supported ink tanks.
A hardware error occurred in an ink tank (the ink tank
LED is turned off). Replace the ink tank(s).
Close the scanning unit (printer cover).
Remove the applicable USB hub from the PictBridge
(USB) connector.
Replace the empty ink tank(s), and close the scanning
unit (printer cover).
Printing with an empty ink tank can damage the
machine.
To continue printing without replacing the ink tank(s),
press the Stop/Reset button for 5 sec. or longer to
disable the function to detect the remaining ink
amount. After the operation, it is recorded in the
machine EEPROM that the function to detect the
remaining ink amount was disabled.
Conditions
encoder signal.
signal.
5 / 41
Solution
(Replacement of listed parts,
which are likely to be faulty)
- Carriage unit (QM3-2650)
- Timing slit film (QC2-5687)
- Logic board (QM3-2834)
- Carriage motor (QK1-1500)
- Timing sensor unit (QM3-
2572)
- Timing slit disk film (QC1-
9597)
- Feed roller (QL2-2206)
- Logic board (QM3-2834)
- Paper feed motor (QK1-3849)
- Purge unit (QM3-2651)