Anchor ProLink 500 Network Gebruikershandleiding - Pagina 3

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Anchor ProLink 500 Network. Anchor ProLink 500 Network 6 pagina's. Wireless intercom

Pagina afdrukken

ProLink 500™ Wireless Intercom Owners Manual

BASIC SETUP AND OPERATION

1. Charge the batteries 5-6 hours.

Note: Belt packs operate about ten to twelve hours of

continuous use per charge. (Diagram 2)

2. Find the MASTER belt pack as indicated on the top label. The

Master belt pack must be ON for each of the REMOTE belt

packs to function. (Diagram 1)

3. Plug headset cable into belt pack & adjust boom. (Diagram 2)

4. Turn on power and set headset volume. Power ON LED is

solid green and flashing green for LOW battery. (Diagram 1)

5. Set slide switch to Push to Talk or Always On mode.

(Diagram 3)

6. Choose channel A or B for all belt packs. If both channels are

used at the same time, two master belt packs are required

(See page 6). (Diagram 1)

Note: repeat above for each member's belt pack in use.

BELT PACK CONTROLS

Mic Gain – controls the microphone sensitivity. Someone with a soft

voice will increase the Mic Gain.

Power Knob also controls headset volume. The Power LED is solid

green while ON and flashes green when batteries need recharging.

A/B Channel Selection – each member of the system must be on the

same channel to hear communication

RX/TX LED – flashes RED when transmitting and is SOLID RED on the

Remote belt packs when out of range of the Master belt pack

PTT control – push to engage in conversation and release when done

Push to Talk or Always ON slide switch for the mode of operation

preferred. If you want hands free operation, select the Always On mode.

Your belt pack is live at all times.

4-PIN XLR headset connector - use Anchor Audio headsets or any

headset with a dynamic microphone.

Charging Port for the GC-9000 gang charger – charge LED glows RED

when charging and stops glowing when charge complete.

HEADSETS

ProLink 500 uses noise cancelling headsets with a 4-pin XLR connector.

Models H-2000 (dual ear muff) and H-2000S (single ear muff) are

available. The headsets include an adjustable boom microphone.

ON/OFF/VOLUME CONTROL

MIC GAIN CONTROL

PROLINK 500 BELT PACK

Model Shown: BP-500M

BLUETOOTH SETUP

1. Turn ON the BT headset and put it in pairing mode to pair ("CONNECT") with ProLink 500 beltpack.

Note: Every Bluetooth headset has its own pairing procedure. Refer to instructions.

2. The BT will auto pair with the ProLink 500 if the BT headset has been already paired to the ProLink 500 beltpack.

3. RED LED will turn ON (see on the back side of ProLink 500) in a few seconds indicating that it has paired.

4. After the RED LED turns ON push the CONNECT button to activate the audio.

5. If you want to switch to the wired headset on the same beltpack you will have to turn

OFF/disconnect the BT headset.

6. If you want to pair a new BT headset push "DISCONNECT" to delete current pairing before you start the pairing process.

For System Setup & Operation Videos Visit Our Website: www.anchoraudio.com

D I A G R A M 1

RX/TX LED (RED)

"PUST TO TALK " BUTTON

CHANNEL SELECTOR

POWER LED (GREEN)

D I A G R A M 2

XLR CONNECTOR

CHARGING PORT

CHARGING LED (RED)

MADE IN USA

TWO YEAR WARRANTY

D I A G R A M 3

"PUST TO TALK " OR

ALWAYS ON SLIDE SWITCH

BATTERY COMPARTMENT

BELT CLIP

BLUETOOTH

PAIRING

PANEL