Andersen Windows & Doors Andersen 1000 Installatiehandleiding - Pagina 3

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Andersen Windows & Doors Andersen 1000. Andersen Windows & Doors Andersen 1000 15 pagina's. Handle set and closer

Pagina afdrukken

3. INSTALL LOCk CASE, kEY CYLINDER AND HANDLES:

w a r n i n g

Do no insert finger into holes drilled in door. Holes have a sharp

edge. Inserting fingers into holes could result in injury.

Insert lockcase into slot in edge of door. Fasten the lockcase

to the door with two (2) #8 x 1/2" screws.

Insert key cylinder through slot of interior trim plate with the

thumbturn on the interior of the door. Fasten key cylinder in

place using #10 x 1-1/2" machine screw.

Place nylon washers over the interior and exterior handles.

Insert the square spindle of the exterior handle through the up-

per hole in the exterior trim plate, through lockcase and push

until square spindle is visible from interior of door.

Slide interior handle onto square spindle. Using the

hex wrench provided, tighten the set screw on the

interior handle. Do not squeeze the handles together

too tightly when tightening the set screw. Tighten

trim plate screws at this time. Test operation for the

handle set with the door standing open.

4. INSTALL LATCH STRIkER:

Extend the deadbolt. Mark the top and bottom of the

deadbolt and latch bolt on the handle side Z-bar.

Open the door and place the striker on the handle

side Z-bar. Center the bottom striker opening vertically

on the deadbolt marks on the handle side Z-bar.

Center the openings in the striker horizontally over the

openings in the handle side Z-bar. Mark the center

of the two (2) slotted mounting holes and remove

the striker. Center punch and drill 3/32" hole at each

location marked.

Place the striker on the handle side Z-bar and fasten it

with two (2) #6 x 1/2" screws.

Check the latch and deadbolt for proper function. If

necessary, adjust the striker forward or back until

the door latches properly. With the striker screws

tightened, center punch and drill two (2) 3/32" holes

through the two (2) center mounting holes in the

striker. Fasten in place with two (2) #6 x 1/2" screws.

Close the door to check for deadbolt clearance.

Slowly extend the deadbolt by turning the thumbturn

knob. If the deadbolt makes contact with the door

jamb, even slightly, chisel a recess into the door jamb.

Chisel the recess deep and wide enough to provide

adequate clearance for the deadbolt.

Chisel the recess deep and wide enough to provide adequate clearance for the deadbolt. Failure to do so may result in the

deadbolt becoming lodged in the door jamb. If deadbolt becomes lodged it can prevent the door from unlocking.

STEP 3a

EDgE OF DOOr

SLOT

LOCkCaSE

#8 X 1/2"

SCrEw

STEP 3C-D

DOOr

EXTEriOr

HanDLE wiTH

SQuarE

SPinDLE

nYLOn

waSHEr

LOCkCaSE

inTEriOr ViEw

STEP 4a-C

DOOr

jaMB

PEnCiL

MarkS

FOr LaTCH

BOLT anD

DEaDBOLT

iF DEaDBOLT

COnTaCTS

DOOr jaMB,

CHiSEL rECESS

inTO jaMB

C A U T I O N

inTEriOr

STEP 3B

TriM PLaTE

DOOr

SLOT

#10 X 1 1/2" SCrEw

inTEriOr ViEw

uPPEr TriM

PLaTE HOLE

nYLOn

waSHEr

inTEriOr HanDLE

TriM PLaTE

SCrEw

STEP 4B-D

HanDLE

SiDE

DOOr

z-Bar

jaMB

#6 X 1/2"

SCrEw

STrikEr

SLOTTED

HOLE

EXTEriOr

ViEw

STEP 4E

HanDLE SiDE

z-Bar

DOOr

jaMB

STrikEr

inTEriOr

TriM PLaTE

kEY CYLinDEr

THuMBTurn

inTEriOr ViEw

SET

SCrEw

HanDLE

SiDE

z-Bar

CEnTEr

MOunTing

HOLE

#6 X 1/2"

SCrEw

STrikEr

EXTEriOr

ViEw

inTEriOr

HanDLE

DOOr

EXTEriOr

HanDLE

TOP ViEw