ATL Berkshire 400 Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} ATL Berkshire 400. ATL Berkshire 400 4 pagina's.

Pagina afdrukken

Preparing to use your

Berkshire 400

INITIAL CHECK

Our telephones are checked, tested and leave us in

perfect condition. If yours is damaged, please return

it to your supplier with proof of purchase, for a

replacement.

TELEPHONE NUMBER LABEL

The telephone incorporates a label underneath the

handset for recording frequently used telephone

numbers. To remove the plastic cover, operate the

release clip with your thumb nail and hinge upward.

CONNECTION

The Berkshire 400 telephone can be connected

either to a Direct Exchange Line, or as an extension

to a compatible company exchange (PABX).

HANDSET CORD

This cord will require connection between the

telephone and handset. Take any end of the handset

cord, locate the port marked 'HANDSET' on the left

hand side of the Berkshire 400 and simply push to

locate. Connect the other end to the base of the

handset to complete.

LINECORDS

The Berkshire 400 arrives with two line cords for

customer selection. Select your required linecord

(standard BS6312 BT-socket, or RJ45 socket for

category 5 installations). The rear of the telephone

has a port marked 'LINE', plug your selected linecord

into this port ﬁ rst and the other end to your telephone

line termination point. An RJ11 line cord is available

as an option, ask your supplier for details.

WALL AND DESK MOUNTING KITS

A wall or desk mounting kit is available as an option,

please contact your supplier for further information.

Using your Berkshire 400

with the Handset

RECEIVING CALLS

Incoming calls will be announced by the audible

ringer and ﬂ ashing LED. To answer the call, simply

lift the handset.

ADJUSTING YOUR RINGER VOLUME

The ringer volume is controlled by a 3 position switch

located at the rear of the telephone and indicated

by the word 'RINGER'. Moving through the settings

from left to right they are 'HIGH', 'MED' and 'LOW'.

ADJUSTING YOUR RINGER PITCH

The ringer pitch control is also a 3 position switch

located at the rear of the telephone and indicated

by the words 'RINGER PITCH'. Settings from left to

right are 'HIGH', 'MED' and 'LOW'.

MAKING A CALL VIA THE HANDSET

•

Pick up the handset and listen for dial tone

•

Dial the required telephone number

(Note: making external calls from a company

exchange (PABX) requires the number to be preﬁ xed

by an access digit, normally '9')

Using your Berkshire 400

with Headset

CONNECTING THE HEADSET

To connect the headset, insert the plug on the

headset cord into the socket marked 'HEADSET' on

the left hand side of the telephone.

NOTE: Headsets used with this telephone must

comply with the standard EN6095.

RECEIVING CALLS

When your telephone rings, the default path for the

call is to the handset. To receive it on the headset,

press 'HEADSET' button once and the call is switched

to the headset. This action will be conﬁ rmed by LED

indication within the headset button. At the end of

the call, press the 'HEADSET' button a second time

to turn the headset off.

MAKING CALLS

Press the 'HEADSET' button to turn the headset

on and dial as normal. When you have ﬁ nished the

call, press 'HEADSET' to turn the headset off.

Whether making or receiving calls the LED will

ﬂ ash if the 'HEADSET' button is pressed and no

headset is connected.

ADJUSTING THE HEADSET VOLUME

You can adjust the volume to the headset, by

pressing the (+) and (-) keys located on the front

face of the Berkshire 400 and marked 'VOLUME'.

TRANSFERRING CALLS

•

FROM HANDSET TO HEADSET

If you have taken a call on the handset and wish

to transfer it to your headset, press 'HEADSET'

and replace the handset.

•

FROM HEADSET TO HANDSET

If you wish to transfer a call from your headset