DANLERS COPD BK Installatie-opmerkingen - Pagina 2

Blader online of download pdf Installatie-opmerkingen voor {categorie_naam} DANLERS COPD BK. DANLERS COPD BK 2 pagina's. Compact person detector, pir switch

Pagina afdrukken

Installation procedure

1. Please read these notes carefully before commencing work.

In case of doubt please consult a qualifi ed electrician.

2. The detector should be sited so that it is not shaded from daylight

3. The detector should be mounted between 1 and 2.2 metres high, via

any of the four pre-drilled mounting holes only.

4. It must be mounted with the cable entering from below.

5. Make sure the power is isolated from the circuit.

6. The detector should be connected as shown in diagram E

L - Live in, N - Neutral in, SL - Switched Line out.

7. IMPORTANT - Replace terminal cover.

8. Once the wiring has been completed and verifi ed, switch on the supply

and test the operation.

Lux and Time set-up

For convenience, ensure that the TIME is set to minimum when setting up

the LUX level. Afterwards set the TIME to a value suitable for the application.

8. When powered up, (after 1 minute stabilisation time) turn lux pot

(diagram C) fully clockwise and time pot fully anticlockwise.

9. Press the MODE button (diagram B) for approximately 0.5s. The

LED will go green indicating the LUX cell is active. (Or press and

hold button for approx. 4 seconds – LED goes RED indicating Lux

cell INACTIVE). Repeating these steps will toggle the functionality.

10. If lux cell active, vacate area until PIR switch switches the load off

(should be after 10 seconds).

11. With the LUX as desired on working plane from daylight ONLY (no

artifi cial light), wind the lux pot anticlockwise whilst waving your

hand in front of the PIR cell. When the PIR switches the load ON,

stop turning the pot. The Lux inhibit level is now set.

12. Turn the PIR time to the desired timeout (diagram D). Whenever a

person is detected, the time lag will start again and the load will stay

switched on.

Precondition

Power-up Condition

Lux Cell Inactive

Relay OFF

Relay comes ON for 1 Min. After 1 min. ready for detection.

Lux Cell Active

Relay ON

Relay stays ON for 1 Min. After 1 min. ready for detection.

Lux Cell Active

Relay OFF

Relay comes ON for 1 Min. After 1 min. ready for detection.

Lux Cell Inactive

Relay ON

Relay stays ON for 1 Min. After 1 min. ready for detection.

A: Detection range

Recommended mounting

height 1 to 2.2 metres

Strong detection zone

(5m) i.e. person walking

towards detector

B: Time/Lux adjusters (inside casing)

2.5m

80s

Dual colour LED:

40s

10m

RED - PIR active,

STATUS

MODE

20s

Photocell inactive

20m

GREEN - PIR and

10s

40m

Photocell override ON

(passive LUX)

min

max

TIME

Time

Delay

Spindle

1000

TIME

LUX

D: Time adjustment

E: Wiring diagram

Inside detector housing

2.5m

80s

optional manual

40s

10m

wall switch for

overriding off

20s

20m

10s

40m

230 VAC

min

max

TIME

Safety cap

Locate safety cap plastic

pins in the hole 'L' and

second 'N' holes above

the termination screws.

Press firmly to attach.

Secondary

detection zone

(10m, 8m at

extremes)

i.e. person

walking

perpendicular to

detector

C: Lux adjustment

Lux Cell

Mode

1000 LUX

max

min

LUX

Lux

Setting

Use Mode Button to disable

Spindle

LUX (see diagram B)

COPD or COPD BK

1000 LUX

10 LUX

max

min

LUX

10 LUX

load