Gage Bilt GB756 Handmatig - Pagina 5

Blader online of download pdf Handmatig voor {categorie_naam} Gage Bilt GB756. Gage Bilt GB756 14 pagina's.

Pagina afdrukken

DESCRIPTION

WARNING:

THE BALANCE OF THIS TOOL IS DESIGNED FOR VERTICAL USE AND IS NOT SUITED FOR ANY

OTHER APPLICATIONS. GAGE BILT WILL BE PLEASED TO ADVISE FOR YOUR SPECIFIC APPLI-

CATION.

The GB756 is a hydraulic installation tool designed specifically for the efficient installation of a wide range of

blind, lockbolt and Magna-Grip® fasteners thru 3/8" diameter. It weighs 11.1 lbs. (5.0kg) and can be operated

in any position with one hand. It has a .960" (24.4mm) rivet setting stroke and a rated pull load of 10,000 lbs

(44.5kN).

The GB756 riveter operates with 90 to 100 psi (6.2-6.9 bar) of air. At 90 psi. (6.2 bar) air pressure, the GB756

does not exceed 81.5 db (A) and consumes 6.0 cfm at 20 cycles per minute.

The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.

Nose Assemblies that were designed for the model 353 installation tool mount directly on the GB756 without

the use of an adapter.

Nose Assemblies that were designed for the model 352 installation tool will attach to the GB756 with the use

of the 353352 nose assembly adapter.

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE ORDERED SEPARATELY

(SEE PAGE 12).

MAINTENANCE

WARNING:

EXCESSIVE CONTACT WITH HYDRAULIC FLUID AND LUBRICANTS SHOULD BE AVOIDED.

WARNING:

MAINTENANCE PERSONNEL

WARNING:

DISCONNECT TOOL FROM ITS AIR SOURCE BEFORE PERFORMING MAINTENANCE.

The performance of any tool depends upon good maintenance practices. Following these minimal require-

ments for service and care will extend the life of your tool.

*Only use an air supply set at 90-100 psi. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full and free of air by using the

air bleeder (704153) on a regular basis.

*Proper care by operator is necessary in maintaining full productivity and reducing down time. Read all

applicable tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris.

*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at

the end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB756TK is recommended.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will

greatly reduce downtime and increase life of

components. Using sewing machine oil, or an

equivalent cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3.Cycle tool 8-10 times and

TORQUE SPECIFICATIONS

Button Head Cap Screws (402479) = 35-40 inch lbs.

Packing Plug (756218) = 45 foot lbs.

Flexlock Nut (A-1089) = 17 foot lbs.

End Cap (756116) = 50 foot lbs

Button Head Cap Screws (402482)= 35-40 inch lbs. (Do NOT over-tighten)

S/N: 1226 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

MUST

wipe dry.

READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS.

Image may not

reflect actual tool

REV. 3/14