ADEMCO Q16 Gebruikersinstructie - Pagina 3
Blader online of download pdf Gebruikersinstructie voor {categorie_naam} ADEMCO Q16. ADEMCO Q16 7 pagina's.
Pagina afdrukken
Operate this function:
"Program+4+*+ 1 +Program"
7 , Extend the Time ofArm
Users can extend the time of Arm when users don't need to arm ·at once
when press the "Arm" Button. The extend time range is from
0~99
seconds.
Route: "Program+5+*+ (numbers)+Program"
Example: Users need to Arm in 5 seconds when press the "Arm" button.
"Program+5+*+ 05+Program"
8, Extend the Time of alarm
Users can extend the time of Arm when users don't need to arm .at once
when press the "Arm" Button. The extend time range is from
0~99
seconds.
Route: "Program+8+*+ (numbers)+Program"
Example: Users need to Arm in 5 seconds when press the "Arm" button.
"Program+8+*+ 05+Program"
9, Sounded Time for Siren when alarm
.'
Users can set the sounded time for the siren when alarm.
"Program+6+*+ (time)+ Program"
For e.g.: set the sounded time 1 minute for the Siren when alarm;
"Program+6+*+ 01+Program". You can set the time form 0-30
Minute, when the setting is more than 30 rninutem the siren will ring until
disarm, Set the time "00" is mute alarm.
10, Remote control the Ringing times ofthe Telephone
Users can limit the ringing times of the telephone connected to the Alarm
control panel. This is used for remote operation to the Alarm control panel.
"Program+7+*+ (numbers)+Program"
Note: set number "0", users can't dial the telephone number which is
connect with the Alarm control panel.
11, Learning the Remote controller &. Detectors
In order to receive the signal from the Remote controller and detectors, all
Alarm control panel should to
learning
ID code from Remote controller and
detectors. Route: "Program+9+·+ (password)+ll+(Zone No.)+Program"
At the same time, the led light on the main panel will flowing flash. Trigger the remote
control or other accessories. the alarm control panel wi II send out a'shot and a long
4
sound of "B", The zone number of remote control must be
0 1
,other accessories can be
learn to any defense zone.
12, Cancel Detectors
Cancel detectors ID code:
"Program+9+*+ (password)+ 20+Program" All the accessories will been
cancel by this route, if want to resurrecti~n, please relearn the code.
13, Cancel Remote controller
Cancel Remote controller ID code:
"Program+9+*+ (password)+ 1 O+Program" All the remote control will been
cancel by this route, if want to resurrection, please relearn the code.
14, Separate ArmIDisarm for each separate zone
Route: "Program+9+*+ (password)+90+(Zone No.)+(O or l)+Program". 0
means this zone will not alarm when it's Arm, namely bypass.
1
means the
alarm function is on, bypass restored.
15, Set the the special phone No. for the arm notice
Route: "set +7+*+Phone number+set". the alarm control panel will send out
a shot and a long sound of"B" to show users' operation is correct.
16, Set the the special phone No. for the disarm notice
Route: "set +8+*+Phone number+set". the alarm control panel will send out
a shot and a long sound of"B" to show users' operation is correct.
17, The ArmIDisarm Notice Function On/OfT
Route: "Program+0+*+10+(0 or l)+Program" . the alarm control panel will
send out a shot and a long sound of "B" to show users' operation is correct.
o
means close, 1 means allow.
18, The ArmIDisarm Phone Display Notice Function On/OfT
Route: "Program+O+*+ 16+(0 or l)+Program" . the alarm control panel will
send out a shot and a long sound of "B" to show users' operation is correct.
o
means close, 1 means allow.
19, Set ID code
Route: "Set+9+*+lD code (4 No.)+ Neighbor's ID code (4 No.) + Set" . the
5