ADEMCO 5890PI Installatie-instructies

Blader online of download pdf Installatie-instructies voor {categorie_naam} ADEMCO 5890PI. ADEMCO 5890PI 4 pagina's. Passive infrared motion detector/transmitter

Pagina afdrukken

For use with Q.E.D. control panels only.

N5987-1 3/98

INSTALLATION INSTRUCTIONS

GENERAL INFORMATION

The 5890PI Passive Infrared Motion

Detector/Transmitter is a battery-operated

wireless device intended for use as part of a

5800 series wireless alarm system.

Designed for use in commercial and

residential installations, the 5890PI is a wall -

mounted unit with a standard lens that

provides wide-angle protection up to a range

of 35 ft (10.6m). For best coverage, mount the

detector so that the likely direction of

intruder motion is across the pattern.

When installed per the guidelines, the Split -

Zone Optics technology in the 5890PI

provides reasonable false alarm protection

against pets and other animals up to 40 lbs.

This

document

provides

instructions for the 5890PI, but the installer

must be familiar with the installation

instructions for the 5800 Wireless Alarm

System with which the 5890PI is intended to

be used.

FEATURES

•

Split-Zone Optics provides pet immunity

against animals up to 40 lbs.

•

Wireless operation for fast installation.

•

Dual-element pyro-electric sensor provides

positive protection while minimizing false

alarms.

•

Alternate polarity pulse count option offers

greater stability in adverse environments.

•

Provision to turn LED on while Walk-

Testing (LED is turned off after testing).

•

Tamper-protected cover – unit transmits

message if cover is removed.

•

Wall or corner mounting options.

SYSTEM DESCRIPTION

Optical System: Uses efficiently designed

Fresnel lenses with Split-Zone Optics.

Radio

Transmitter:

The

transmitter serves only as the communication

link to the alarm system's Receiver/Control,

and can send alarm, tamper, supervisory, and

battery status messages to the system's

receiver/control. The transmitter is not used

for detection purposes. Each detector has a

unique ID code permanently assigned at the

factory. You must enroll this ID into the

control system at the time of installation.

This allows each detector used in the system

to be uniquely identified. You must program

the control to enroll the 5890PI as an "RF"

type unit (i.e., supervised RF).

To conserve battery life during normal

operation, no more than one transmission

sequence will occur within a 3-minute period.

There is no such time restriction in "Test"

mode.

Alternate Polarity Pulse Count: Two

jumper-selectable detection response modes

are provided: Instant response (Pulse Count

OFF) and Alternate Polarity Pulse Count

(Pulse Count ON). With Pulse Count OFF,

any detected change in infrared energy will

trigger an immediate alarm signal. This mode

is recommended when the detector is used to

monitor a narrow hallway where coverage is

provided by only a single zone.

Use the Pulse Count ON mode when the

detector is installed in areas where periodic

changes in infrared energy levels are normal

(for example, where forced-air heating ducts

are present). In this mode, at least two

changes in infrared energy must be detected

within a short period before an alarm will be

triggered.

Important

applications,

recommended.

SPECIFICATIONS

Pet Immune

Lens

installation

Pulse Count:

Detectable

Walk Rate:

Mtg. Height:

Walk Test

Indicator:

Batteries:

0perating

Temperature:

Operating

Humidity:

Dimensions:

built-in

25'

(7.6m)

25'

(7.6m)

7.5'

(2.3m)

Protection Pattern

PASSIVE INFRARED MOTION

DETECTOR/TRANSMITTER

Note: For

pet

immune

Pulse

Count

35 ft x 45 ft

(10.6m x 13.7m).

30 zones (8 long, 7 over 7

intermediate, 4 over 4

short range).

Installer-selectable

On/Off link.

0.5 – 10 ft/sec

(0.15 - 1.5m/sec).

7.0 ft recommended (2.1m),

but may be mounted at

other heights (see Table 1).

Red LED with

Test/Normal (disable) link.

Two 3-volt Lithium

batteries. Use only

Ademco No. 466,

Duracell DL123A,

Panasonic CR123A,

Sanyo CR123A or

Varta CR123A.

32 F – 122 F (0 C - 50 C).

Up to 95% RH (max.), non-

condensing.

2-11/16"W x 5"H x 1-7/8"D

68mm x 127mm x 48mm.

ALTERNATE

COUNT POLARITY

EACH ZONE CONSISTS

OF 2 FIELDS

10'

20'

30'

35'

(3m)

(6m)

(9m)

(10.6m)

10'

20'

30'

35'

(3m)

(6m)

(9m)

(10.6m)

Figure 1.

Previous Menu

No. 5890PI

BATTERY INSTALLATION

1. Remove front cover by inserting a large

screwdriver blade (or small coin) in groove

between cover and base at the location

shown in Figure 2; rotate blade to

override snap fit, then lift cover off.

2. Observing correct polarity, install the

two Lithium batteries (supplied) into the

battery holders, as shown in Figure 5.

Make sure the batteries are firmly seated.

3. Replace the cover (snap fit).

Battery Caution:

Risk of fire, explosion, and burns. Do not

recharge, disassemble, heat above 100 C, or

incinerate. Dispose of used batteries

promptly. Keep away from children.

Programming Note: If you have not

programmed the detector's ID into the

system (i.e., this is an initial detector

installation), refer to the PROGRAMMING

section below and perform the ID enrolling

procedure before mounting or testing the

detector.

PROGRAMMING

You must enroll the detector's ID during

installation of the system. You should

program the 5890PI as an "RF" type unit

(i.e., supervised RF). and the "Loop"

number as "1".

To program the detector, place the LED

jumper in the TEST position (see Figure 5),

the Pulse Count jumper in the OFF position,

batteries installed and cover on. Temporarily

cover the lens (a cloth will do) to prevent any

activation by the detector.

With the control in Zone Programming mode,

at the "Input serial number" prompt, remove

the cloth cover and motion your hand over the

lens to activate the detector and cause it to

send a FAULT; then cover the lens again to

send a RESTORE. Repeat this procedure to

confirm the serial number enrolled.

Alternatively, you can enter the serial

number manually.

Return LED jumper to the NORMAL

position.

See the control unit's installation instructions

for further details.

INSTALLATION HINTS

•

Do not install where the detector is exposed

to direct sunlight or directly above strong

sources of heat.

•

Make sure the detection area does not have

obstructions (curtains, screens, large pieces

of furniture, plants, etc.) which may block

the pattern of coverage.

•

Avoid locating a unit in areas which

contain objects likely to produce a rapid

change in temperature, such as central

heating, radiators, or ducts (or heaters of

any kind), air conditioners, open flame, etc.

•

Do not mount on an unstable surface.