Autonics BYD DDT Series Producthandleiding - Pagina 2

Blader online of download pdf Producthandleiding voor {categorie_naam} Autonics BYD DDT Series. Autonics BYD DDT Series 5 pagina's. Photoelectric sensors with built-in timer

Pagina afdrukken

Ordering Information

This is only for reference, the actual product does not support all combinations.

For selecting the specified model, follow the Autonics website.

BYD

❶

❷

❸

❶ Sensing distance

Number: Sensing distance (unit: mm)

Number+M: Sensing distance (unit: m)

❷ Sensing type

T: Through-beam

D: Diffuse reflective

D: Convergent reflective

❸ Power supply

D: 12 - 24 VDCᜡ

❹ Output

T: Solid state (transistor)

Sold Separately

• Bracket B

• M12 connector cable: C□D(H)4-□-□

Cautions during Installation

• Be sure to install this product by following the usage environment, location, and specified

ratings. Consider the listed conditions below.

- Installation environment and background (reflected light)

- Sensing distance and sensing target

- Direction of target's movement

- Characteristic curves

• When installing multiple sensors closely, it may result in malfunction due to mutual

interference.

• For installation, tighten the screw with a torque of 0.5 N m. Mount the brackets correctly to

prevent the twisting of the sensor's optical axis.

• Do not impact with a hard object or bend the cable excessively. That could decrease the

product's water resistance.

• Use this product after the test. Check whether the indicator works appropriately for the

positions of the detectable object.

Through-beam

Emitter - Receiver:

Install to face each other

Timer Setting

• In case of the built-in timer model, you can set the OFF Delay timer.

(adjustable time: 0.1 to 2 sec)

• Use the offered adjustment screwdriver. Do NOT turn with excessive force to prevent product

damage.

Min.

Max.

Operation Timing Chart and Indicators

■ Standard type

Operation mode

Light ON

Received

Received light

Interrupted

Operation

indicator (red)

OFF

Transistor output

OFF

• In case of the through-beam type, to prevent malfunction, output of units keeps the state of OFF

for 0.5 sec after power ON.

■ Built-in timer type

Operation mode

Light ON

Received

Received light

Interrupted

Operation

indicator (red)

OFF

Transistor output

OFF

• T: Setting time by the adjuster (setting time: 0.1 to 2 sec)

• t: ≤ 3 ms (When the adjuster is set to Min (0.1 sec))

• If the interrupted time (Ta) after receiving the light is shorter than the setting time (T),

the transistor output maintains the ON state.

❹

❺

❻

❺ Connection

No mark: Cable type

W: Cable connector type

❻ Control output

No mark: NPN open collector output

P: PNP open collector output

(Through-beam type)

❼ Feature of convergent reflective type

No mark: Front operation indicator

U: Upper operation indicator

T: Built-in timer (OFF delay mode)

• Slit for through-beam type: BYD3M-ST (sticker)

Reflective

Sensor - Sensing target:

Install to face each other (parallel with the

sensing side of the unit)

Dark ON

Received

Interrupted

OFF

Connections

■ Cable type

• Emitter

• Receiver (BYD3M-TDT2-□), Diffuse reflective,

❼

(BYD3M-TDT1-□)

Convergent reflective type

Brown

NPN

Blue

01) Through-beam type: max. 100 mA, diffuse reflective or convergent reflective type: max. 50 mA

■ Cable connector type

Circuit

■ NPN open collector output

OCP

SCP

01) Through-beam type: max. 100mA, diffuse reflective or convergent reflective type: max. 50 mA

• OCP (over current protection), SCP (short circuit protection)

• If short-circuit the control output terminal or supply current over the rated specification, normal control signal is

not output due to the protection circuit.

Sensitivity Adjustment

• Set the adjuster for stable Light ON area, minimizing the effect of the installation environment.

• Use the offered adjustment screwdriver. Do NOT turn with excessive force to prevent

product damage.

• The steps below are based on Light ON mode.

STEP Status

Description

Received

Interrupted

Dimensions

• Unit: mm, For the detailed drawings, follow the Autonics website.

• This dimensions shows the cable type.

Refer to the 'Specifications' for the core, wiring and connector.

12.4

Ø3.5, 2m

Through-beam

Optical axis

Upper operation indicator of convergent reflective type (red)

Sensitivity adjustment adjuster or timer adjuster of built-in timer model

■ Bracket A

Brown

LOAD

Black

PNP

01)

Blue

Color

①

Brown

②

③

Blue

④

Black

• Connector pin ④ is N.C (not connected) terminal

for the emitter.

■ PNP open collector output

LOAD

OCP

SCP

01)

Turn the adjuster from MIN to MAX sensitivity and

check the position (A) where the operation indicator

activates under the light ON area.

Turn the adjuster from (A) to MAX and check the

position (B) where the operation indicator activates

under the light OFF area.

If the operation indicator does NOT activate at the

MAX (maximum sensitivity): MAX = (B).

Set the adjuster at the mid position between (A) and

(B) for optimal sensitivity.

12.4

Ø3.5, 2m

Diffuse reflective,

Convergent reflective

21.5

Max. 100 mA

LOAD

Function

0 V

OUT

Max. 100 mA

LOAD