Highlander iP-2 Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} Highlander iP-2. Highlander iP-2 4 pagina's. Dual system - integrated pickup and preamp for acoustic guitar and bass dual system - integrated pickup and preamp for acoustic guitar and bass

Pagina afdrukken

iP-2 INSTALL ATION

i P- 2 I N S TA L L AT I O N

O R A G O O D W O O D W O R K E R W I T H E X P E R I E NC E W O R K I N G O N ACO U ST I C S T R I N G E D IN S T RU M E N TS .

O R A G O O D W O O D W O R K E R W I T H E X P E R I E N C E W O R K I N G O N ACO U S T I C S T R I N G E D I N S T R U M E N TS .

Parts Included:

Qty. Description

Pre-wired iP-2 Pickup/Preamp Assembly with an Access Jack

For connecting a 2nd source

Battery Holder Clips for 9 Volt Battery

Pieces of Self Adhesive Velcro® for cable strain relief

Stereo Mini-Plug for connecting a second transducer to the iP-2

Tools Required:

HAND DRILL or ELECTRIC DRILL (cordless preferred)

MILLING MACHINE or ROUTER AND SADDLE SLOTTING JIG

Used for routing the groove

3)*

17/32" (13.5mm) DRILL BIT, RELIEVED ON RAKE EDGES

Used for drilling guitar end block for the strap jack

4)*

9/16"-12 TPI NC TAP & MACHINIST'S TAP HANDLE

Used for threading end block to accept the strap jack

5)*

1/16" (1.6mm) DIAMETER BALL ENDED END MILL

Used for routing the groove in the bottom of the saddle slot

3/32" (2.5mm) TWIST DRILL BIT

Used for drilling both holes in the saddle slot for the pickup

MILLING MACHINE or DISC / BELT SANDER or

MACHINIST'S VISE AND FILE. STRAIGHT EDGE

Used for reducing saddle height to

compensate for the pickup thickness

* The following installation tools are available from Highlander:

17/32" drill bit

9/16"-12TPI tap bit

1/16" router bit

These tools are available individually or as the 'iP-installation kit'

About the Output Jack

The iP-2 is turned on when a guitar cord is plugged in

and turned off when it is unplugged, saving the battery.

Tip:

Pickup and Preamp Out

Ring: 2nd Source Out

Shield: Ground

The 2nd source is hard wired

from the Tip of the Access Jack

to the Ring on the Output Jack.

The iP-2 does not include a 2nd

preamplifier for the 2nd source.

Output Jack

This innovative screw thread is designed

to stay in place regardless of variations in

the end block as it expands and contracts

due to humidity and temperature changes.

By eliminating the typical machine thread

and nut, our preamp will never come loose

and require the awkward task of tightening

a nut at the end pin block inside the guitar.

The elegant strap button holds the strap

securely and will never untwist or loosen.

The information and graphics contained in this document are the property of Highlander Musical Audio Products. Copying of any kind is prohibited, except for personal use only.

T H I S I N S TA L L AT I O N S H O U L D O N LY B E U N D E R TA K E N BY A N E X P E R I E N C ED LU T H I E R

T H I S I N S TA L L AT I O N S H O U L D O N LY B E U N D E R TA K E N B Y A N E X P E R I E N C E D LU T H I E R

Using the wrong techniques or tools could result in permanent damage to your guitar.

Highlander is not responsible for any damage resulting from the installation of this pickup system.

For optimum pickup per f r formance and ease of installation, please take a

For optimum pickup pe

ormance and ease of installation, please take a

moment to read through this Installation Guide before beginning. Thank You.

About the Access Jack

The Access Jack (AJ) is a 3.5mm Stereo Female Jack that enables a

2nd Source to be used with the iP-2 including a magnetic sound hole

pickup or an electret microphone such as our 'Internal Mic' . Power for

active pickups or electret microphones is provided on the ring of the AJ.

The power at the AJ is 'on' only when the guitar is plugged in.

Both signals are available separately at the output Jack, enabling both

sources to be connected to separate sound systems or amplifiers.

Both signals can be combined using a good quality mixer such as our

'Pro Acoustic Mix DI'.

Always Use a Stereo Male to connect to the Access Jack.

When connecting a mono source, the stereo plug must still be used

with the ring left unconnected.

Never use a Mono Male to connect to the Access Jack.

+9 Volt power on the ring will be shorted out causing the battery

to seriously overheat.

If this inadvertenlty happens during installation, the battery has been

compromised and must be changed.

A High Quality 3.5mm Stereo Male is provided with every iP-2.

Typical wiring for the 3.5mm Stereo Mini Jack

Wiring for a Phantom Powered, Electret Microphone.

Tip Ring

Sleeve

Wiring for a Passive Magnetic, Sound Hole Pickup.

For more information check out our web site:

Tip:

2nd Source Audio

Ring:

+9 Volt for 2nd Source

Shield: Ground

Ring must be left open

(unconnected)

Hot

Shield

Tip

Shield

Ring must be left open

(unconnected)

Hot

Shield

Tip

Shield

ighlanderpickups.com

Highlander Musical Audio Products 1991-2009

Electret

Condenser

Mic

Magnetic

Pickup