IKEA IX5HHEXWS09 Gebruiksaanwijzing - Pagina 10
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} IKEA IX5HHEXWS09. IKEA IX5HHEXWS09 40 pagina's. Whirlpool
Pagina afdrukken
5.
If you need to clean the condenser:
•
Remove the base grille.
•
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
•
Replace the base grille when finished.
Plug in refrigerator or reconnect power.
Freezer door models
Top of the refrigerator compartment
- Slide the shield
toward the back to release it from the light assembly.
Top of freezer compartment
- Squeeze and pull rear of
light shield toward you to release the tabs, then pull down.
Ctscssg "sg '@Lght
s.s &_ __,_
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with an appliance bulb of the same size, shape,
and wattage (no greater than 40 watts).
1. Unplug the refrigerator or disconnect power.
2. Remove the light shield, if necessary.
Freezer drawer models
Top of the refrigerator compartment
- Slide the light shield
toward the back of the compartment to release it from the
light assembly.
Top of freezer compartment
- The light shield opens from
the back. Firmly press forward on the notches in the back
of the shield and pull the shield down.
NOTE: You may need to remove the upper freezer shelf or
basket to access the light assembly.
3. Replace the burned-out bulb(s) with an appliance bulb(s) no
greater than 40 watts.
4. Replace the light shield.
Freezer drawer
models
Top of the refrigerator compartment
- Insert the tabs on
the shield into the liner holes on each side of light
assembly. Slide the shield toward the front until it locks
into place.
NOTE: To avoid damaging the light shield, do not force
the shield beyond the locking point.
Top of the freezer compartment
- Insert the front tabs of
the shield into the liner and snap the back portion of the
shield over the light assembly.
Freezer door models
Top of the refrigerator compartment
- Insert the tabs on
the shield into the liner holes on each side of the light
assembly. Slide the shield toward the front until it locks.
NOTE: To avoid damaging the light shield, do not force
the shield beyond the locking point.
Top of freezer compartment
- Insert front tabs of light
shield into liner and snap the back of the shield over light
assembly.
5. Plug in refrigerator or reconnect power.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
The refrigerator
will not operate
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow these instructions can result in death,
fire, or electrical
shock.
•
Power cord unplugged?
Plug into a grounded 3 prong outlet.
10
Is outlet working?
Plug in a lamp to see if the outlet is
working.
Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
Are controls
on? Make sure the refrigerator controls are on.
See "Using the Control(s)."
New installation?
Allow 24 hours following installation for the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency
compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with explanations.