Kohler 19517 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} Kohler 19517. Kohler 19517 2 pagina's. Lavatory faucet/bidet faucet single lever /single control

Pagina afdrukken

INSTALLATION

How To Install The Faucet

The product you have selected has quick, drop-in installation feature.

Flush the water supply pipes thoroughly to remove debris.

Slip the washer(1) over the flexible hoses and mounting stud, and into

the groove on the body assembly.

If needed to take off the hoses to repair, reinstall and tighten them by

hand.

①Insert flexible hoses and tighten it. Insert the washer(2) and the

connecting nut(3) into the hole in deck. Position the connecting nut

between flexible hoses.

②Center the washer and faucet over hole. Tighten with supplied

wrench. Check that the nut is centered and flexible hoses hang freely.

Attach the hoses to water supplies. When facing front of faucet, the

left hose is hot water, the right hose is cold water.

For 9076A-4ND

Insert the plug(4) into hole on the back of the faucet if not install

pop-up drain.

How To Install The Drain(Not For 9076A-4ND /9076-ND)

Remove flange(6) from drain body(8). Slide the washer(7) onto the

underside of the drain flange. Apply thread tape to tailpiece(9) and

install it to drain body(8). Insert drain body from underside of bidet

with drain lever hole (13) facing to the back of the bidet. Thread

flange(6) onto drain body by hand. Tighten the locknut(12) by hand

from the underside .

Place stopper(11) into drain body aligning the flat side of stopper

hole(10) with the drain lever hole.

NOTE: If needed apply a ring of plumbers putty around the underside

of the drain flange(6), instead of using washer(7).

Place the rubber washer(14) into the drain lever hole. Put another

plastic washer(15) and retaining nut(16) into the long end of the ball

lever rod(17).

Insert the ball lever assembly(18) into the drain lever hole and through

the stopper hole, and tighten the retaining nut.

Be sure that the ball lever points to the back of the bidet. Tighten the

locknut on the drain body. Remove any excess putty.

NOTE: Do not reposition the drain after the locknut is tightened, or

you may break the putty seal.

836770A-C

Assemble thumb screw(21) to link(22), and link onto ball lever rod

with 'V' clip(23). Slide lift rod(20) through hole in faucet and into the

hole in link. Position the lift rod so bottom of the lift rod knob(19) rests

against the faucet body.

Push the ball lever down into the open position.

Tighten thumb screw.

Connect the tailpiece(24) to the trap(25). The tailpiece should extend

25mm to 50mm into the trap.

INSTALLATION CHECKOUT

Ensure that all coupling nuts are tight.

Ensure that the lever handle is in the down position.

Open the drain.

Turn on the main water supply, and check for leaks. Repair as

needed.

Remove the aerator(26). Run hot and cold water through the faucet

for about one minute to remove any debris. Check for leaks. Remove

any debris from the aerator assembly. Shut the faucet off, and

reinstall the aerator assembly.

CLEANING INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean

soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could

adversely affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Kohler faucets and fittings.

836770A-C