Avocet 15 Handmatig - Pagina 2
Blader online of download pdf Handmatig voor {categorie_naam} Avocet 15. Avocet 15 2 pagina's.
MILES OR KILOMETERS. When you install the battery, the Cy-
clometer displays "SEL" and "km" flashes. You can choose whether
miles or kilometers will be displayed by pressing the right button.
After you have made your selection, press the left button to go to
wheel size calibration.
If you want to switch between miles and kilometers after initial setup,
you must remove the battery. When you do this, stored data us lost
and the calibration number is reset to 2155.
Change the blinking
digit of the calibration
CALIBRATION. "Cir" is on the top display and the right digit of
number with the right
the calibration number flashes on the lower display. Find the cali-
button
bration number that matches your tire size from the table, or mea-
sure tire circumference by the precise calibration method. Adjust
the flashing digit with the right button, then press the left button to
go to the next digit. When all the digits are adjusted, press the left
button to exit.
You can also change the calibration number without removing the
battery. In the Total Distance function (D) press both buttons to
display the calibration number. Then hold both buttons down for
to enter calibration. Set the calibration number as described above.
STEP 1 – TRANSMITTER.
Position the
magnet housing over a pair of crossed spokes
with the spokes inside the slots. Insert the mag-
net in the well and close the housing pressing
the parts together until they lock together over
the spokes.
Magnet Housing
Magnet
Spoke
BATTERY & TROUBLESHOOTING
INSTALLING A NEW BATTERY.
move the battery by prying up the cap with a
screwdriver. Install the new battery with its
positive (+) side toward the cap, then press in
the cap. Use only an Avocet Cyclometer 15
battery or equivalent (see specifications). Af-
ter battery installation a blinking "km" appears
on the display. Press the left button for "mi".
Press the right button to calibrate. The default
calibration number 2155 will appear. Any num-
ber other than 2155 indicates improper reset, and
the battery must be removed then reinstalled after
waiting at least 10 minutes.
STEP 2– RECEIVER.
Position the receiver
on the right fork blade opposite the magnet.
Insert a zip tie through the slot and secure it
loosely on the fork. Rotate the wheel until the
transmitter is behind the receiver, then adjust
the receiver on the fork so that it is opposite
the magnet. Rotate the receiver until it is
3
/
" from the transmitter magnet then tighten
16
the tie and trim off its free end with scissors.
Magnet
Receiver
1
/
"
8
TROUBLESHOOTING
Re-
Speed and distance seem too high or
too low
Check calibration number
Confirm calibration number by tire roll-
out
Check spacing between receiver and
transmitter
No speed or distance
Check transmitter/receiver alignment
and spacing
Check contacts on back of Cyclometer and
on mount and clean with a pencil
eraser if necessary
Check for broken wire
No display or display dim
Replace battery
Incorrect data or unusual display
Remove battery, then reinstall after
15 secondss
CALIBRATION
CALIBRATION NUMBERS. The calibration number is wheel circumference in milli-
meters. This table is based on popular tire brands and assumes recommended inflation
pressure and a rider weight of 165 lbs. (75 kg). To account for your unique combination of
weight, tire pressure, and tire model, measure your tire circumference.
Tire Size
Number
20 x 1.75
1528 mm
24 x 1
1753
600 tubular
1759
650 tubular
1929
26 x 1
1913
26 x 1.25
1952
26 x 1.5
1986
Calibration number equals tire circumference in inches multiplied by 25.4, or in millimeters.
PRECISE CALIBRATION. For the most precise calibration of your Cyclometer, measure
the tire's 'rolling circumference' by the following method: Inflate your tires to your usual
riding pressure. Mark the ground under the valve stem when the stem is at its lowest point.
Get on the bicycle and have a helper push you in your normal riding position until the
valve stem returns to its lowest point. Take care that the tire travels in a straight line. Mark
below the stem again, then measure the distance between the marks in inches or millime-
ters. If you measure in inches, multiply your measurement by 25.4 to convert to millime-
ters. The calibration number is the tire circumference in millimeters.
INSTALLATION
STEP 3 - RECEIVER WIRE.
to the inside of the fork with cable ties, then wrap
the wire around the front brake cable until the ex-
cess has been used up. Attach the wire only to parts
that rotate when the bicycle is steered–the fork,
handlebar stem, or the front brake cable. Do not
attach the wire to the head tube.
1
/
to
8
Brake Cable
Tie
AVOCET 1-YEAR LIMITED WARRANTY
This Avocet Cyclometer is warranted against defects in material and workmanship for one year after date of purchase, or
two years after the manufacture date stamped on the PC board under the battery (YM), whichever comes first. Defective
products will be repaired or replaced. The warranty will not cover the battery, normal wear, damage, or loss and is void if
the Cyclometer is disassembled by anyone other than an authorized Avocet Service Center.
Customer service and product information are available at www.avocet.com/service.html or by calling 650-470-0478.
Warranty claims are to be sent to the Service Center by the owner, not by the retail store where the Cyclometer was purchased.
Include a description of the problem. Only the original, dated cash register or charge card receipt will be accepted for proof
of purchase date (no exceptions).
Send your Cyclometer freight prepaid to the Service Center at the address listed below. A traceable method of shipment is
recommended in the event that your shipment to Avocet is lost in transit.
Customer service and product information are available at www.avocet.com or by calling 650-470-0478 ext 218
Tire Size
Number
26 x 1.95/2.0
2045 mm
26 x 2.1
2056
26 x 1
3
/
2068
8
700C tubular
2083
700 x 20
2081
700 x 23
2087
700 x 25
2091
STEP 4 – MOUNT BRACKET.
Attach the wire
ber shim around the handlebar near the stem. Re-
move the clamp screw and place the bracket on the
handlebar over the shim. If the shim is too long,
trim it shorter with scissors. Insert the clamp screw
and tighten it until the bracket is secure. Slide the
Cyclometer into the bracket from front to rear until
it snaps on. Spin the wheel and confirm that a speed
reading is displayed. If the display remains at zero,
check that the receiver and transmitter magnet are
Tie
1
aligned and
/
to
8
Receiver
PROCESSING INFORMATION
Avocet Service Center
170A University Ave.
Palo Alto, CA 94301
AVOCET, INC, P.O. Box 180, Palo Alto, CA 94302, USA
Tire Size
Number
700 x 28
2096 mm
700 x 32
2116
700 x 38
2159
27 x 7/8
2077
27 x 1
2105
27 x 1 1/8
2123
27 x 1 1/4
2142
Wrap the rub-
3
/
" apart.
16
0402