AVS RM43 Installatiehandleiding - Pagina 4
Blader online of download pdf Installatiehandleiding voor {categorie_naam} AVS RM43. AVS RM43 5 pagina's.
Ook voor AVS RM43: Installatiehandleiding (4 pagina's)
Pagina afdrukken
AVS RM70C
WIRE COLOUR
FUNCTION
RED
+12/24v ACC supply
BLACK
Earth
GREEN
Switches display to C2
C2 4 pin connector
C2 camera input & power
C1 4 pin connector
C1 camera input & power
BUTTON
FUNCTION
POWER
Power on/off
+
Adjust display brightness/contrast up
MENU
MENU – push to enter menu and scroll through functions
-
Adjust display brightness/contrast down
V1/V2
Manually switch between camera inputs
AVS RM90C
The AVS RM90C can display up to 4 cameras in a split screen, either any channel full screen, 2 way or 4 way split.
The channels can be switched manually using the buttons on the front panel or remote or can be controlled by each channels input wire
e.g. connect the blue wire to the left turn indicator and mount camera 3 on the left side of the vehicle. When the left indicator turns on
the monitor will display the left side camera. Do not connect any input control wire to permanent power as this will lock the display to
that channel and may damage the monitor.
WIRE COLOUR
FUNCTION
RED
+12/24v ACC supply
BLACK
Earth
GREEN
Switches display to CH2 REVERSE
BROWN
Switches display to CH1 FORWARD
BLUE
Switches display to CH3 LEFT
GREY
Switches display to CH4 RIGHT
CH2 (REV) 4 pin
CH2 camera input & power
connector
CH1 (FWD) 4 pin
CH1 camera input & power
connector
CH3 (L) 4 pin
CH3 camera input & power
connector
CH4 (R) 4 pin
CH4 camera input & power
connector
BUTTON
POWER
MODE
MENU
CH1/<
CH2/>
CH3/Ú
CH4/Ù
CONNECT TO
Appropriately fused +12/24v switched ignition on supply
Good earth source e.g. vehicle body/chassis
Reverse signal/vehicle reverse light wire (+12/24v)
4 pin camera cable. Monitor will switch to display this input when a signal is
detected on green wire e.g. when the car goes into reverse. Display will switch back
to C2 or turn off if there is no signal on C1.
4 pin camera cable. Monitor will display C1 until a signal is detected on green wire.
FUNCTION
Power on/off
Switch between 1/2/3/4 camera display. See options below
MENU –push to enter menu and scroll through functions. See options below
Manually switch to CH1 camera or adjust left
Manually switch to CH2 camera or adjust right
Manually switch to CH3 camera or adjust down
Manually switch to CH4 camera or adjust up
CONNECT TO
Appropriately fused +12/24v switched ignition on supply
Good earth source e.g. vehicle body/chassis
Reverse signal/vehicle reverse light wire (+12/24v)
Forward camera switch (+12/24v)
Left turn indicator or switch (+12/24v)
Right turn indicator or switch (+12/24v)
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on GREEN wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on BROWN wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on BLUE wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on GREY wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed