Dell S5048F-ON Firmware bijwerken - Pagina 16
Blader online of download pdf Firmware bijwerken voor {categorie_naam} Dell S5048F-ON. Dell S5048F-ON 19 pagina's.
Ook voor Dell S5048F-ON: Installatiehandleiding (29 pagina's)
Pagina afdrukken
If you were previously in ONIE Update mode and stopped discovery using the onie-stop command, restart discovery using
the onie-start command. This command causes the ONIE firmware updater infra to locate the firmware updater binary
image and proceed with the firmware update.
Verify firmware update
After you have updated the firmware, verify that all components—BIOS and CPLD, are running the correct version.
● To check the BIOS version, use the dmidecode -s system-version command. The BIOS version also displays during
system bootup.
● To check the CPLD version, use the showSystemInfo command if you are using Dell DIAGs. Or use the
cpldupgradetool --cpldver command if you are using EDA-DIAGs.
Firmware update using USB
ONIE Discovery can locate a valid self-updater image in a USB.
1. Rename the firmware updater image so that it matches the onie-self updater image name.
For example, onie-firmware-x86_64-dellemc_<platform>_c2538-rx.x.xx.x.x-x.bin. Where <platform>
is the name of the switch and x.xx.x.x-x is the firmware version.
2. Copy the renamed image to the USB.
3. Insert the USB in the target system.
4. Boot the target system to ONIE Self-Update mode.
ONIE Discovery locates the image on the USB and starts the firmware update process.
Booting `ONIE: Update ONIE'
ONIE: ONIE Update Mode ...
Version
: x.xx.x.x-x
Build Date: 2022-08-03T09:57-0700
Info: Mounting kernel filesystems... done.
Info: Mounting ONIE-BOOT on /mnt/onie-boot ...
random: fsck urandom read with 15 bits of entropy available
ERROR: fsck corrected errors.
Info: Mounting EFI System on /boot/efi ...
Info: Using eth0 MAC address: 34:17:eb:37:2d:00
scsi 6:0:0:0: Direct-Access
sd 6:0:0:0: [sdb] 7888896 512-byte logical blocks: (4.04 GB/3.76 GiB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or
FUA
sd 6:0:0:0: [sdb] Attached SCSI removable disk
Info: eth0:
Checking link... up.
Info: Trying DHCPv4 on interface: eth0
random: nonblocking pool is initialized
Warning: Unable to configure interface using DHCPv4: eth0
ONIE: Using link-local IPv4 addr: eth0: xxx.xxx.xx.xxx/xx
Starting: dropbear ssh daemon... done.
Starting: telnetd... done.
discover: ONIE update mode detected.
Starting: discover... done.
Please press Enter to activate this console. Info: eth0:
Info: Trying DHCPv4 on interface: eth0
Warning: Unable to configure interface using DHCPv4: eth0
ONIE: Using link-local IPv4 addr: eth0: xxx.xxx.xxx.xxx/xx
ONIE: Starting ONIE Service Discovery
FAT-fs (sda7): Invalid FSINFO signature: 0x82564557, 0x61417272 (sector = 1)
ONIE: Executing installer: file://dev/sdb/onie-updater
Verifying image checksum ... OK.
Preparing image archive ... OK.
Firmware: Version
Firmware: Architecture
Firmware: Machine
Firmware: Machine Rev
Firmware: Config Version: 1
=============== ONIE FW UPDATER ===============
16
USB
Flash Disk
Running updater.
: x.xx.x.x-x
: x86_64
: dellemc_<platform>_c2538
: 0
8.07 PQ: 0 ANSI: 4
Checking link... up.