Epson L200 Servicehandleiding - Pagina 29
Blader online of download pdf Servicehandleiding voor {categorie_naam} Epson L200. Epson L200 47 pagina's. Color inkjet printer
Ook voor Epson L200: Specificaties (4 pagina's), Gebruikershandleiding (4 pagina's), Instructies (4 pagina's), Start Here (2 pagina's), Gebruikershandleiding (2 pagina's), Kennisgevingen en garantie (12 pagina's)
Pagina afdrukken
L200/L201/L100/L101
Tube Guide Plate Support
Section A
Tube Guide Plate
Cross-
OK
Tube Guide Plate
section
Tube Guide Plate Support
Hole A
NG
Tube Guide Plate
Refer to the figure above and follow the procedure below when installing the Tube Guide Plate Support.
1. Make sure that the hole B of the Tube Guide Plate Support comes on the right front side as seen from the front of the printer, and route the Tube
Guide Plate Support through the hole A (x2) of the Tube Guide Plate as shown in the "OK" image above.
2. Route the ink tubes along with the Tube Guide Plate.
3. Insert the section A of the Tube Guide Plate Support into the hole C of the Tube Guide Plate Support up from the bottom as shown in the "OK"
image above to secure it
Middle Housing (L200/L201)
Left side
Middle Housing
10.0 mm
45.0 mm
Voluntary Label
When replacing the Middle Housing, peel off the Voluntary Label
from the old housing and attach it to the new housing as specified
in the figure above.
Disassembly/Assembly
Tube Guide Plate Support
Section A
Hole A
Hole C
Hole B
Hole C
Hole B
OK
NG
Section A
Hole C
Ink Tube
Ink Supply Holder Assy (L200/L201)
1
Ink Supply Holder Assy
C.B.P-TITE SCREW 3x6 (5.0 ~ 6.0 kgf·cm)
When installing the Ink Supply Holder Assy, align the hooks (x2)
with the hole of the Middle Housing, and tighten the screws in the
order indicated in the figure above.
Details of Disassembling/Reassembling by Parts/Unit
Refilling Ink Label (L200/L201)
8.0 mm
Hole C
Section A
Ink Tube
Attach the Refilling Ink Label on the position shown in the figure
above.
Ink Tube Guide 1st
Middle Housing
C.B.P-TITE SCREW 2.5x5
(5.0 ~ 6.0 kgf·cm)
2
Follow the procedure below when removing the Ink Supply Holder Assy / Ink Tube Guide 1st.
1. Remove the screws (x2) that secure the Ink Supply Holder Assy.
Hook
2. Peel off the acetate tape (x2) that secure the Ink Tube Guide 1st.
3. Remove the screw (x1) that secures the Ink Tube Guide 1st.
4. Release the hooks (x2) that secure the Ink Tube Guide 1st, and remove it from the frame.
5. After confirming the Valve is closed, disconnect the Ink Tubes from the Joint.
6. Pull out the Ink Tubes from the holes of the Middle Housing / Ink Supply Holder Assy / Ink Tube Guide 1st, and remove the Ink Supply Holder
Assy / Ink Tube Guide 1st.
16.5 mm
30.5 mm
Refilling Ink Label
6.4 mm
Attach the Valve Position Label on the position shown in the figure
above.
Ink Tube Guide 1st / Ink Supply Holder Assy (L200/L201)
Joint
Ink Tube
Ink Tube Guide 1st
Hook
(p 29)
(p 27)
(p 10)
Revision A
Valve Position Label
7.5 mm
7.5 mm
Valve Position Label
Ink Tube Guide 1st
Holes
Ink Tube
Ink Supply Holder Assy
Middle Housing
29
Confidential