AmpliVox SW800-96-03 Podręcznik użytkownika - Strona 6

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla System głośników AmpliVox SW800-96-03. AmpliVox SW800-96-03 12 stron. Titan wireless battery powered pa system

Drukuj stronę

96 CHANNEL UHF WIRELESS

WIRELESS RECEIVER PANEL (SINGLE)

• Channel Display (A)

• Select Buttons -

Manual Channel Selection (B)

• Volume Control (C)

RECEIVER SETUP:

• The receiver has its own POWER / VOLUME Control (C). Turn Power On. Chan-

nel Display (A) will show "ON" and show last channel used. To select a clear

channel, press SYNC (D) button. Receiver will scan for the next clear channel and

stop. Also turn on the Wireless Transmitter (Bodypack or Microphone) and press

the SET (R-handheld or L-bodypack) button. Display will FLASH and then sync

to Receiver.

• To manually select a channel, press and hold either the UP or DOWN ARROW

BUTTON (B) for 1 second until channel number is flashing. Then select new chan-

nel. Stop pressing button when you have the channel you want.

Channel number must match channel number on wireless transmitter.

• When receiving signal, the RX Indicator (F) will light to show that a radio frequen-

cy is being received. Then when speaking, AF Indicator (E) will light to show that

audio is being received. If no lights, then check the channel selection on both the

receiver and transmitter.

• A/B DIVERSITY ANTENNA INDICATOR (G): Receiver has two antennas and

selects which antenna is receiving the best signal. Will light Red or Green.

WIRELESS BODYPACK MICROPHONE TRANSMITTER SETUP:

• The transmitter bodypack is operated by 2 - "AA" 1.5 Volt alkaline batteries. Slide

off battery cover (H) and install batteries as shown. Observe correct polarity when

inserting batteries. Make certain the batteries are fully seated in their compartment

so the cover slides in place easily. Close cover. Battery life with alkaline batteries

is approximately 8 hours of operating time.

• Slide ON/OFF (I) switch to ON position. POWER LED (J) and DISPLAY (K) will

light and ON will appear for a second then switch to show BATTERY STATUS and

CHANNEL currently set to. To automatically sync to the same channel that ap-

pears on the wireless panel receiver press SET Button (L) and then press SYNC

button on Receiver Panel (D). Both displays will FLASH and sync to the same

channel.

• To manually select and match the channel number on the receiver, you PRESS

and HOLD the SET BUTTON (L) a few seconds until the channel number starts to

flash. Release SET BUTTON and using the UP/DOWN BUTTONS (M), select new

channel. Press SET BUTTON again to lock in CHANNEL. Channel selected

should match channel on receiver. When transmitter and receiver are set to correct

channel the RX INDICATOR (F) on receiver will glow green.

• Plug the Lapel / Headset microphone into the MIC INPUT JACK (N). The lapel

microphone can be clipped to clothing, using the supplied clip. The lapel mic

should be placed under the chin, as close to the center of the body as possible.

MUTE (O): If you temporarily want to silent the microphone without turning it off,

●

push MUTE BUTTON down. When ready to use microphone again, press MUTE

BUTTON to release, and begin to speak.

• SENSITIVITY SWITCH (P): If you are a soft spoken person then set the switch to

the HI position. If you are a loud speaking person then set the switch to the MID or

LOW position. Adjust to prevent distortion while speaking.

• AUX IN (Q): This 1/8ʺ (3.5mm) jack allows you to connect and wirelessly play au-

dio from any phone, tablet, laptop or other media-playing device that has an audio

output jack.

• When done speaking, slide ON/OFF switch to OFF.

SEE PAGE #9 FOR DUAL

• Channel Sync (D)

• AF - Audio Frequency Indicator (E)

• RX - Radio Frequency Indicator (F)

• Antenna Indicator (G)

Wireless Transmitter - Bodypack

Front Panel

Top Panel

Side Panel

Back Panel