Bosch FAP-OC 500Series Instrukcja obsługi i konserwacji / instrukcja instalacji - Strona 34

Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji / instrukcja instalacji dla Spryskiwacz Bosch FAP-OC 500Series. Bosch FAP-OC 500Series 40 stron. Built-in wall ovens
Również dla Bosch FAP-OC 500Series: Instrukcja instalacji (21 strony), Instrukcja obsługi (40 strony), Instrukcja instalacji (6 strony), Informacje o produkcie (40 strony), Instrukcja instalacji (28 strony), Podręcznik użytkownika (48 strony), Podręcznik użytkownika (48 strony), Instrukcja instalacji (28 strony), Instrukcja obsługi i konserwacji (44 strony), Instrukcja instalacji (32 strony), Skrócona instrukcja obsługi (4 strony), Instrukcja obsługi i konserwacji (27 strony), Instrukcja instalacji (24 strony), Instrukcja instalacji (32 strony), Instrukcja obsługi i konserwacji (24 strony), Instrukcja instalacji (28 strony), Instrukcja serwisowa (41 strony), Instrukcja obsługi i konserwacji (21 strony), Instrukcja instalacji (32 strony), Instrukcja serwisowa (36 strony), Instrukcja instalacji (32 strony), Skrócona instrukcja obsługi i bezpieczeństwa (13 strony)

Bosch FAP-OC 500Series Instrukcja obsługi i konserwacji / instrukcja instalacji
Problem
Water has not drained
completely.
Water is coming out
from underneath the
washer.
Foam comes out of the
detergent dispenser
drawer.
The cyle status
sequence Wash flashes
in the display.
Repeated spinning.
No spin took place
(laundry is still wet).
Detergent residue on
the laundry.
System shakes or
shudders when spin
speed increases.
34
Possible cause(s)
Suds may be excessive (usually
due to too much detergent or non-
HE detergent being used).
Pump is blocked.
Drain hose or drain pipe is blocked. Clean drainage pipe and/or drainage hose.
Water supply hose is leaking: is not
screwed on tight at both ends, or
rubber washer not placed in hose.
Drain hose is leaking.
Too much detergent was used, or a
non-HE detergent was used; pump
was not able to pump out the
increased suds.
The Unbalanced Load Detection
system is attempting to balance the
load through repeated spins.
Load size too small.
Large items may have become
entangled in the drum and could
not be distributed by the Unbal-
anced Load Detection system; spin
cycle therefore canceled for safety
reasons.
Excessive suds: too much deter-
gent was used, or a non-HE deter-
gent was used.
No Spin was selected
Some phosphate free detergents
contain water insoluble ingredients
that may appear as light spots on
the laundry.
The washer drum suspension sys-
tem shifts during spinning as the
speed increases. This may result in
a slight shaking of the washer
during the spin speed transition.
Solution(s)
Use less detergent for future loads. Be sure to use
only high efficiency HE-detergents.
Check and clean the drain pump, water drain hose
and/or the drain pipe.
Eliminate the cause: tighten the hose (by hand at the
washer end), check for rubber washer in place.
Check the drain hose, be sure that it is on the washer
securely with the clamp in place; may need to replace
the drain hose if leaking continues.
Immediate fix: mix 1 tablespoon of fabric softener with
1/2 liter (1 pint) of water and pour this mixture into the
detergent compartment (not with waterproof fabrics).
To prevent: use less detergent for future wash loads.
To prevent: always load the washer with a mixture of
large and small wash items (easier to distribute in the
drum).
Add more laundry.
To prevent: always load the washer with a mixture of
large and small wash items (easier to distribute in the
drum).
Immediate fix: mix 1 tablespoon of fabric softener with
1/2 liter (1 pint) of water and pour this mixture into the
detergent compartment (not with waterproof fabrics).
To prevent: use less detergent for future wash loads.
Select a spin speed setting (Low, Med or High)
Brush off when laundry is dry or
execute the program Rinse.
Mix small and large laundry items together in the load
to minimize this effect. Check to be sure the washer is
level and all four feet press equally against the floor.
Transport bolts removed?
~ Remove the transport bolts; Page 13