Care and cleaning
The efficiency of the range hood system depends on
the cleanliness of the intake and filters.
The frequency of cleaning depends on the amount
and type of cooking.
• Do not use the ventilating system without the
filters in place or with grease-laden filters or
surfaces.
To avoid risk of fire and explosion do not use
flammable liquids or solvents.
Always unplug or disconnect the appliance from the
power supply before servicing.
Be sure the entire hood (including the filters and light
bulbs) has cooled and grease has solidified before
attempting to clean any part of the appliance.
Filters
Filters
Filters
Filters
Filters
The metal grease filters are made of stainless steel
anodized aluminum and are long lasting.
T T T T T o Remove The Metal Gr
o Remove The Metal Gr
o Remove The Metal Gr
o Remove The Metal Grease Filters
o Remove The Metal Gr
ease Filters
ease Filters
ease Filters
ease Filters
• Turn the fan and lights off.
• Pull the spring release handle.
T T T T T o Replace The Metal Gr
o Replace The Metal Grease Filters
o Replace The Metal Gr
o Replace The Metal Gr
o Replace The Metal Gr
ease Filters
ease Filters
ease Filters
ease Filters
• Reverse procedure.
T T T T T o Clean Filters
o Clean Filters
o Clean Filters
o Clean Filters
o Clean Filters
• • • • • It is recommended that the filters be washed at
least once a month; they can be washed by hand
or in the dishwasher.
• Drain water through edge holes and let each filter
dry thoroughly before replacing it.
Care and cleaning
Lights
Lights
Lights
Lights
Lights
Before replacing the lamps, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally.
NOTE: Tur ur ur ur urn of
NOTE: T
NOTE: T
NOTE: T
NOTE: T
n off the lights and fan. Allow the lights
n of
n of
n of
f the lights and fan. Allow the lights
f the lights and fan. Allow the lights
f the lights and fan. Allow the lights
f the lights and fan. Allow the lights
to to to to to cool
cool
cool
cool
cool befor
befor
befor
befor
before handling.
e handling. If new lights do not
e handling.
e handling.
e handling.
If new lights do not
If new lights do not
If new lights do not
If new lights do not
operate be sure lights ar
operate be sur
operate be sur
e lights are inserted corr
e lights ar
e lights ar
e inserted corr
e inserted corr
e inserted correctly befor
operate be sur
operate be sur
e lights ar
e inserted corr
calling service.
calling service.
calling service.
calling service.
calling service.
Replace Lights
Replace Lights
Replace Lights
Replace Lights
Replace Lights
• Remove the inner lamp lens cover by inserting a
small flat blade screwdriver into each of the three
slots and gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
• Grasp the bulb and pull it straight out.
• Replace with 12 volt, 20 watt halogen bulbs with
a G4 base SUITABLE FOR USE IN OPEN
LUMINAIRES.
Follow package dir
Follow package dir
Follow package dir
Follow package dir
Follow package directions, wear gloves, do not
ections, wear gloves, do not
ections, wear gloves, do not
ections, wear gloves, do not
ections, wear gloves, do not
touch bulb with your bar
touch bulb with your bar
touch bulb with your bare fingers.
touch bulb with your bar
touch bulb with your bar
• Replace inner cover by inserting the three
retaining tabs into the three slots and pressing
them firmly in place.
ectly befor
ectly before e e e e
ectly befor
ectly befor
e fingers.
e fingers.
e fingers.
e fingers.
Bulb
19
19
19
19
19
Drukuj stronę