ANSMANN POWERLINE 5 PRO Podręcznik - Strona 4

Przeglądaj online lub pobierz pdf Podręcznik dla Sprzęt oświetleniowy ANSMANN POWERLINE 5 PRO. ANSMANN POWERLINE 5 PRO 5 stron.
Również dla ANSMANN POWERLINE 5 PRO: Podręcznik (20 strony)

Drukuj stronę

USING THE CHARGER IN A VEHICLE

Connect the DC charging cable to the charger. Connect the DC

charging cable to the 12V DC car socket of your vehicle (Do not

use in 24V DC truck sockets!). Please make sure that the power

of the socket is switched on. Some cars require the ignition to be

switched on.

The charger is now ready for use. You can insert one 9V E-block

and up to 4 AA/AAA/C/D (in any combination) NiMH or NiCd rechar-

geable batteries. You can also connect an USB cable using the

USB charging socket to charge other devices, for example; mobile

phone, smart phone or MP3 player. Insert all batteries with correct

polarity, corresponding to the symbols in the charging slot.

CHARGING OF ROUNDCELLS

The charger has 3 function buttons; "CURRENT", "DISPLAY" and

"MODE" (see illustration [2A]). Using these buttons, it is possible

to use the following settings:

1. MODE button

Push the "MODE" button within 8 seconds of inserting 1-4

rechargeable batteries, to access one of the following charging

programs:

a. CHARGE: Charges battery. After charging is complete, charger

will automatically switch to trickle charging (Trickle charge

will commence after all modes)

b. DISCHARGE: Discharges battery before charging to minimize

the "memory effect" of batteries

c. REFRESH: "DISCHARGE REFRESH" or "CHARGE REFRESH" status

is shown on the LCD display when charger cycles between

discharging and charging. This process will refresh old bat-

teries and bring them back to the maximum capacity. Refresh

will be repeated (max. 10x) until the charger can no longer

d. TEST: Fully charges battery. LCD display shows "CHARGE TEST"

Discharges battery and measures capacity. The LCD display

shows "DISCHARGE TEST". Recharges battery, ready for use.

LCD display shows "CHARGE TEST".

2. CURRENT button

Push the "CURRENT" button within 8 seconds of selecting a char-

ging program or after inserting batteries in order to select the

charging current for the program "CHARGE" or "TEST". Alternati-

vely, choose the discharging current for the program "DISCHARGE"

or "REFRESH".

3. DISPLAY button

Push the "DISPLAY" button whilst charging or discharging to

display the charging/discharging current (mA), the voltage of the

rechargeable battery (V), the charging/discharging capacity (mAh

or Ah) or the remaining charging/discharging time (hh:mm).

Deutsch |

English

Once the settings have been selected, the charger automati-

cally starts with the selected parameters after 8 seconds. If no

settings are chosen, the LCD display will flash after inserting

the rechargeable batteries. First the voltage of the rechargeable

batteries as well as the pre-set charging program "CHARGE" is

shown. Next, the pre-set charging current of 600mA is shown.

After 8 seconds the charging process starts automatically using

the pre-set parameters.

By using the 4 charging slot buttons (see illustration [2B]) you

can make individual settings for each rechargeable battery. To

change a function for a single rechargeable battery, press the

corresponding button below the charging slot for the chosen

battery. The display will flash for this battery and you can now

change settings, as described above, for the single charging slot

using the function buttons "MODE" and/or "CURRENT".

If only one or two rechargeable batteries are inserted into the

charger using the two outer charging slots, in the mode "CHARGE"

and "TEST" the charging current can be increased up to 1500mA

or 1800mA with the "CURRENT" button. In this case the inner

charging slots are disabled and cannot be used. When charging

three or four rechargeable batteries at the same time, the

charging current can be set to 400mA, 600mA or 800mA. Using

the programs "DISCHARGE" and "REFRESH" discharging currents of

200mA, 300mA or 400mA can be selected. The charging current is

generally twice as high as the chosen discharging current.

A few minutes before the rechargeable batteries are completely

charged, the charger reduces the charge current to ca. 200mA,

regardless of the previously selected charge current. This gentle

full-charging extends the service life of your rechargeable

batteries.

After every charge/discharge procedure is complete, the charger

adds a short pause for the benefit of the rechargeable batteries

before continuing with the selected charging/discharging

program.

ATTENTION: Please ensure that the rechargeable batteries are

designed for the respective charging current. For example, AAA

rechargeable batteries should not be charged with a 1500mA or

1800mA charging current! We recommend choosing the maximum

charging current (mA) so that it does not exceed the capacity

value (mAh) of the inserted rechargeable battery.

It is normal that batteries may become warm during charging.

After charging is complete, the charger switches automatically to

trickle charge. The trickle charge prevents self-discharge of the

batteries when left in the charger.