ADEMCO LYNXR Series Skrócona instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla System bezpieczeństwa ADEMCO LYNXR Series. ADEMCO LYNXR Series 8 stron.

Drukuj stronę

Step

Enhanced Sequential Mode - Press *83, then follow the prompts as follows:

Zone Number

entered. The system will announce the Voice Descriptor for the selected zone number, if it is

programmed.

Press [*] to continue. Starting with this zone, the system will search for the first transmitter,

which has all of the following attributes pre-programmed in Zone Programming.

Notes: 1. If the first zone number entered does not have one or more of the above attributes, the

Enroll Mode - If " L " is displayed, the serial number for this transmitter has already been entered,

however, it may still be confirmed, viewed or deleted.

% 0'

Note:

b zz

Serial Number

transmission or manually. If using RF Learning proceed to c. 1). If using the manual mode skip to

c. 2).

Note:

Enter 2-digit zone number of the first transmitter to have its serial number

The correct input type selected in *56 (RF, UR, or BR programmed)

The correct loop number selected in *56

No serial number programmed

Zone type

system will search its database for the first zone that does, and will display it at the

ENROLL SERIAL NUMBER prompt (1b).

2. Pressing 00 exits mode, upon which the prompt "83" blinks, indicating the mode is

inactive.

If the transmitter's serial number has not been previously entered, enter the enroll serial

number mode now by pressing "1", or copy the last serial number that was entered by

pressing "2".

If the transmitter's serial number has been previously entered, it may be viewed by pressing

"3" or deleted by pressing "9".

If view is selected; each digit will be re-displayed, and the keypad will beep once for digits 1-

6, and three times for the last digit.

Once the serial number has been entered the system will return to the (1A) prompt and " L " will

be displayed.

This point can be faulted and restored and the panel will listen for the transmission.

The serial number/loop number combination that was entered can be confirmed by faulting

and restoring the zone being entered. If the panel receives a transmission that matches the

serial number and loop number entered, the keypad will beep three times, and "C" will be

displayed. This indicates that the serial number transmission has been confirmed to match.

No further transmissions will be received.

When confirming a 4-button key, it assumed that all loops are used and only the serial

number is confirmed. Pressing any key will allow a confirm. Two beeps indicate that the

template has been accepted. A single long beep indicates illegal entries, or duplicate serial

number/loop entry.

When the last zone has been entered, the display will remain on that zone. To exit this mode

and return to data field program mode, press 00 at the ZONE NUMBER prompt

Once all zones have been programmed, test each zone using the system's Test mode. Do not

use the Transmitter ID Sniffer mode for this, since it will only check for transmission of one

zone on a particular transmitter, and not the zones assigned to each additional loop.

- This prompt can be used to enroll the transmitter serial number via RF

RF Learning - Two (2) transmissions (two key depressions at least five second apart) will be

required for BR type or four (4) transmissions (fault, restore and fault, restore) for UR or RF

type. BR type devices can be enrolled only by transmission from BR devices. Likewise, UR

and RF devices can only be enrolled by transmission from a UR or RF device.

If the learned serial number has a different loop number than that entered in *56 the system

will announce the Voice Descriptor, if it is programmed, followed by two beeps and will return

to Prompt (1A) and "L" will be displayed.

If the loop number captured by RF transmission and that entered in *56 mode match, the

system will announce the Voice Descriptor, if it is programmed, followed by three beeps and

return to Prompt (1A) and "LC" will be displayed. No additional transmissions are needed for

confirmation.

BR type devices can be enrolled only by transmission from BR devices. Likewise, UR and RF

devices can only be enrolled by transmission from a UR or RF device.

Action

-4-