ADEMCO LYNXR-EN Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla System bezpieczeństwa ADEMCO LYNXR-EN. ADEMCO LYNXR-EN 8 stron.

Drukuj stronę

4XL.N6WDUW*XLGHIRU/<1;5/<1;5DQG/<1;5(1

8 /

LYNXR and LYNXR-EN are not intended for UL985 Household Fire applications unless a 24-hour backup

battery (P/N LYNXRCHKIT-HC) is installed.

Introduction

This Quick Start Guide can help you install the rechargeable LYNXR/LYNXR24 and LYNXR-EN quickly and easily

by providing the basic steps for installation using the built-in defaults. For more detailed information and important

notes, refer to the LYNXR Series Installation Instructions.

The following steps assume that one of the system's default tables will be used.

For programming data values and Powerline Carrier Devices other than those listed in the default tables, see the

Installation Instructions.

Default Table Summary

Zone

-------

front door

back door

window

motion detector

-------

loop 3 arm away

loop 2 disarm

loop 4 arm stay

loop 1 restore device 1

loop 3 arm away

loop 2 disarm

loop 4 arm stay

loop 1 restore device 1

Master User Code

Installer Code

Duress Code

Entering Program Mode: installer code + 8 0 0

Interactive Mode

* 56 Enhanced Zone Programming

* 83 Sequential Mode

*84 Assign Zone Voice Descriptors

Exiting Program Mode: * 99 allows re-entry into the Program mode using Installer Code + 8 0 0.

* 98 inhibits re-entry into the Programming mode using the Installer Code.

NOTES: • Tables 2 and 4 support the automatic paging feature (open/close events reported to pager phone number),and a Powerline

Carrier Device programmed as device 8, which closes and stays closed upon burglary alarms and restores after bell timeout. For

other applications or actions (e.g., using a pulsing siren), see the *80 Device Programming Menu Mode section of the Installation

Instructions.

• Primary report format for all tables is Ademco's Contact ID reporting. Tables 2 and 4 also use Contact ID for secondary

reporting. Tables 1, and 3 use 4+1 format for secondary reporting.

• Table 2 records all events in the event log. Tables 1, 3, and 4 record only alarms, alarm restores, troubles, and trouble restores

in their event logs.

Table 1

-------

front door

back door

Garage door

motion detector

smoke detector

-------

loop 3 arm away

loop 2 disarm

loop 4 arm stay

loop 1 restore device 1

loop 3 arm away

loop 2 disarm

loop 4 arm stay

loop 1 restore device 1

duress

silent alarm

audible alarm

1-2-3-4

4-1-1-2

------

/<1;56HULHV

Table 2

-------

front door

back door

window

motion detector

smoke detector

loop 3 arm away

loop 2 disarm

loop 4 close device

loop 1 restore device 1

loop 3 arm away

loop 2 disarm

loop 4 close device

loop 1 restore device 1

duress

silent alarm

1-2-3-4

6-3-2-1

2-5-8-0

Used to Program

Zone characteristics, report codes, and serial numbers

5800 Series transmitter serial numbers

Voice descriptors for each zone

K5966 5/01 Rev. B

Table 3

-------

front door

back door

window

motion detector

smoke detector

loop 3 arm away

loop 2 disarm

loop 4 close device

loop 1 restore device 1

loop 3 arm away

loop 2 disarm

loop 4 close device

loop 1 restore device 1

duress

silent alarm

1-2-3-4

4-1-1-2

------

Table 4

duress

1-2-3-4

4-1-1-2

------