AutomationDirect SOLO Basic SLB4848-V0 Skrócona instrukcja obsługi - Strona 4

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Kontroler temperatury AutomationDirect SOLO Basic SLB4848-V0. AutomationDirect SOLO Basic SLB4848-V0 4 stron.

Drukuj stronę

Alarm Outputs

For models equipped with alarms there are two alarm outputs. Each alarm can be programmed for one of nine

different alarm types. To set up the first alarm output, press the

button repeatedly until the parameter

ALA1

parameter

ALA1

is not available. Use the

to the chart below for alarm type information. Press the

alarm outputs are required press the

•

button to proceed to

the additional alarm. When the desired alarm(s) are programmed, press the

controller returns to the main screen.

The alarm output limits are controlled by the parameters

alarm output chosen. After selecting the desired alarm, press the

and/or

appears. Use the

alarm outputs selected. Press the

;

button to save each selected value. Press the

return to the controller main screen.

For advanced alarm options

and alarm delay

Al1o

al2o

descriptions in chapter 3 of the user manual.

ALA1

and

ALA2

are both SPST resistive load 3A @ 250 VAC, normally open relay outputs with a shared

common.

Set Value

Alarm Type

Alarm function disabled

Deviation upper- and lower-limit:

Alarm output activates when PV value is higher than the setting value SV+(AL-H) or

lower than the setting value SV-(AL-L).

Deviation upper limit:

Alarm output activates when PV value is higher than the setting value SV+(AL-H).

Deviation lower limit:

Alarm output activates when PV value is lower than the setting value SV-(AL-L).

Absolute value upper and lower limit:

Alarm output activates when PV value is higher than the setting value AL-H or lower

than the setting value AL-L.

Absolute value upper limit:

Alarm output activates when PV value is higher than the setting value AL-H.

Absolute value lower limit:

Alarm output activates when PV value is lower than the setting value AL-L.

Hysteresis upper limit alarm output:

Alarm output activates when PV value is higher than the setting value SV+(AL-H). The

alarm output turns OFF when the PV value is lower than the setting value SV+(AL-L).

Hysteresis lower limit alarm output:

Alarm output activates when PV value is lower than the setting value SV-(AL-H). The

alarm output turns OFF when the PV value is higher than the setting value SV-(AL-L).

Disconnection Alarm: This alarm output is enabled if the sensor connection is

incorrect or has been disconnected.

Error Display Information

The chart below shows the possible error displays on the Solo Basic temperature controller.

Controller Error Display

Display Position

Display

Meaning

No sensor input

Cont

sen

Sensor type error

err

Notes:

;

button for three seconds. Press the

appears. If the controller is configured for dual output control,

button to choose the set value for the desired alarm type. Refer

;

button to save the selected value. If additional

ALA2

. Follow the same procedure to program

;

button repeatedly until the

and

, where "n" corresponds to the

•

button repeatedly until the parameter

and

buttons to enter the high and/or low values for each

;

please reference the parameter

al1d

al2d

Alarm Output Operation

Output is OFF

OFF

SV-(AL-L)

OFF

SV-(AL-L)

OFF

AL-L

OFF

AL-L

OFF

SV+(AL-L) SV+(AL-H)

OFF

SV-(AL-H)

Cause

Corrective Action

Check the input wiring. If the problem still exists, replace the

The input terminals

are open.

sensor or the controller.

Check sensor type and its condition. If damaged or wrong,

Temperature is out of

replace and update settings. Check actual condition to make

range for sensor type

sure temperature is within sensor range.

Parameter Default Settings

•

Display

1234

Use

RUN/STOP: Control setting RUN/STOP

r-S

SELECT POINT: Decimal point setting (0: integer; 1: one decimal point)

LOCK: Setting lock mode (LOCK1: all; LOCK2: only SV changes are allowed)

LoC

ALARM1 HIGH: Upper limit alarm 1 (display according to the setting in ALARM mode)

AL1H

ALARM1 LOW: Lower limit alarm 1 (display according to the setting in ALARM mode)

AL1L

ALARM2 HIGH: Upper limit alarm 2 (display according to the setting in ALARM mode)

AL2H

button again to

ALARM2 LOW: Lower limit alarm 2 (display according to the setting in ALARM mode)

AL2L

OUT1: Display and adjust output value of 1st output group

out1

OUT2: Display and adjust output value of 2nd output group (display when

out2

output mode)

OUT1 MAX.: Upper limit % of 1st output group

o1ma

OUT1 MIN.: Lower limit % of 1st output group

o1mC

OUT2 MAX: Upper limit % of 2nd output group (display when

o2mA

OUT2 MIN: Lower limit % of 2nd output group (display when

o2mi

INPUT: Set input type (refer to section 11 for a list of supported temperature sensors)

inpt

TEMP. UNIT: Set temperature unit C/F

tpun

"TEMP. HIGH: Set up upper temperature limit

tp-h

SV+(AL-H)

(the upper limit setting is different for different types of sensors)"

"TEMP. LOW: Set up lower temperature limit

tp-l

(the lower limit setting is different for different types of sensors)"

SV+(AL-H)

CONTROL: Select control modes (3 different modes: ON-OFF, PID, and MANUAL)

Ctrl

SELECT HEAT/COOL: Select heating, cooling or dual-output heating and cooling.

S-HC

ALARM1 SET: Set up Alarm 1 mode (refer to section 13 "Alarm Outputs")

ALA1

ALARM1 OPTION: Set up Alarm 1 options

Al1o

ALARM1 DELAY: Set up Alarm 1 delay

al1d

AL-H

ALARM2 SET: Set up Alarm 2 mode (refer to section 13 "Alarm Outputs")

ala2

ALARM2 OPTION: Set up Alarm 2 options

al2o

AL-H

ALARM2 DELAY: Set up Alarm 2 delay

al2d

AT: Auto tuning (display when setting

P: Proportional Band (display when setting

I: Integral Time (display when setting

D: Deviation Time (display when setting

PD OFFSET: PD offset when Integral = 0 to eliminate a consistent deviation (display when setting

pdof

= PID automatically set after auto tuning)

Ctrl

OUT1 HYSTERESIS: Adjust Output 1 hysteresis (when

o1-s

SV-(AL-L) SV

OUT2 HYSTERESIS: Adjust Output 2 hysteresis (when

o2-s

OUT1 HEAT: Heating control cycle for Output 1 (when

o1-h

OUT1 COOL: Cooling control cycle for Output 1 (when

o1-C

o2-h

OUT2 HEAT: Heating control cycle for Output 2 (when

OUT2 COOL: Cooling control cycle for Output 2 (when

o2-C

COEF: Proportional band coefficient of Output 1 against Output 2 (when

Coef

in dual output control)

dead

DEAD: Set up deadband (when

PV FILTER: Set up input filter factor of PV

pv-f

PV RANGE: Set up input filter range of PV

pv-r

PV OFFSET: Adjust input compensation of PV

pvof

PV GAIN: Adjust input gain of PV

pv6a

ANALOG OUT1 MAX.: Adjust upper limit compensation for analog Output 1 (1 scale = 1 μA)

a1ma

ANALOG OUT1 MIN.: Adjust lower limit compensation for analog Output 1 (1 scale = 1 μA)

a1mi

Parameter Default Settings

Description

to set temperature set point. Press

•

to switch digits and

s-hC

is set to a dual output mode)

s-hC

is set to a dual output mode)

s-hC

= PID/RUN)

Ctrl

= PID automatically set after auto tuning)

Ctrl

= PID automatically set after auto tuning)

Ctrl

= PID automatically set after auto tuning)

Ctrl

= ON/OFF)

Ctrl

= ON/OFF)

Ctrl

= PID/MANUAL)

Ctrl

= PID/MANUAL)

Ctrl

= PID/MANUAL)

Ctrl

= PID/MANUAL)

Ctrl

is not set to MANUAL and when in dual output)

Default Setting

;

to set value.

RUN

OFF

4.0

0.0

is set to a dual

0.0

100.0

0.0

100.0

0.0

1300

-200

PID

OFF

30.0

120

50.0

Output type:

C: 1 sec

V: 5 sec

R: 20 sec

= PID and when

1.00

0.000