AutomationDirect SOLO SLM Series Skrócona instrukcja obsługi

Przeglądaj online lub pobierz pdf Skrócona instrukcja obsługi dla Kontroler temperatury AutomationDirect SOLO SLM Series. AutomationDirect SOLO SLM Series 4 stron. Modular temperature controllers

Drukuj stronę

SOLO SLM

Quick Start Guide

SOLO Modular Temperature Controllers

SLM Series

This Quick Start Guide provides basic information on setting up the SOLO SLM temperature

controllers. For advanced setup visit the AutomationDirect web site at www.AutomationDirect.com.

Product Support

• For product support, specifications, and installation troubleshooting, a

complete User Manual can be downloaded from the On-line Documentation

area of the AutomationDirect web site.

• For additional technical support and questions, call our Technical Support

team @ 1-800-633-0405 or 770-844-4200..

Safety Information

WARNING: To minimize the risk of potential safety problems, you should follow all applicable local

and national codes that regulate the installation and operation of your equipment. These codes

vary from area to area and it is your responsibility to determine which codes should be followed,

and to verify that the equipment, installation, and operation are in compliance with the latest

revision of these codes.

Equipment damage or serious injury to personnel can result from the failure to follow all applicable

codes and standards. We do not guarantee the products described in this publication are suitable

for your particular application, nor do we assume any responsibility for your product design,

installation, or operation.

If you have any questions concerning the installation or operation of this equipment, or if you

need additional information, please call us at 1-800-633-0405 or 770-844-4200.This publication is

based on information that was available at the time it was printed. At Automationdirect.com® we

constantly strive to improve our products and services, so we reserve the right to make changes

to the products and/or publications at any time without notice and without obligation. This

publication may also discuss features that may not be available in certain revisions of the product.

WARNING! ELECTRIC SHOCK DANGER

1. The SLM series is an OPEN-TYPE device and therefore should be installed in an enclosure free of

airborne dust, humidity, and vibration. The enclosure should prevent non-maintenance staff from

operating the device (e.g. key or special tool is required to open the enclosure).

THIS CONTROLLER IS AN OPEN-TYPE TEMPERATURE CONTROLLER. MAKE SURE TO EVALUATE ANY DANGEROUS

APPLICATION IN WHICH A SERIOUS HUMAN INJURY OR SERIOUS PROPERTY DAMAGE MAY OCCUR.

1. Be sure to tighten terminals to the correct torque of 0.19 Nm. Use solid or twisted wire from 14AWG

to 28AWG.

2. Protect the controller from dust or foreign objects to prevent controller malfunction.

3. Do not modify or disassemble the controller.

4. Do not connect anything to the unused terminals.

5. Make sure all wires are connected to the correct polarity of terminals.

6. Do not install and/or use the controller in places subject to: (a) Dust or corrosive gases and liquid (b)

High humidity (c) Vibration and shock (d) EMI / RFI (e) high temperature.

7. Power must be turned off when wiring, installing or uninstalling expansion modules (SLM2), or

changing a sensor.

8. Be sure to use wires that match the thermocouple types when extending or connecting the

thermocouple wires.

9. Use wires with correct resistance when extending or connecting a platinum resistance thermometer

(RTD).

10. Keep the wire as short as possible when wiring a platinum resistance thermometer (RTD) to the

controller and route power wires as far as possible from load wires to prevent interference and

induced noise.

11. This controller is an open-type unit and must be placed in an enclosure away from high temperature,

humidity, dripping water, corrosive materials, airborne dust and electric shock or vibration.

12. Make sure power cables and signals from instruments are all installed properly before energizing the

controller, otherwise serious damage may occur.

13. To prevent electric shock, do not touch the terminals in the controller or try to repair the controller

when power is applied.

14. Use a soft, dry cloth to clean the controller. Do not use acid or alkaline liquids for cleaning.

15. This instrument is not furnished with a power switch or fuse. Therefore, if a fuse or power switch

is required, install the protection close to the instrument.

16. Note: This controller does not provide overcurrent protection. Use of this product requires that

suitable overcurrent protection device(s) must be added to ensure compliance with all relevant

electrical standards and codes. A suitable disconnecting device should be provided near the

controller in the end-use installation.

3505 HUTCHINSON ROAD

CUMMING, GA 30040-5860

General Description

AutomationDirect's SOLO Modular units are a single loop temperature controller that can

control heating or cooling processes. Depending upon the particular model of controller, the

available outputs include relay, voltage pulse, linear voltage, or current. Available with twelve

selectable alarm types. SOLO Modular controllers have two control outputs that can be used

for control of a heating or cooling applications, alarm output, or for retransmitting the process

variable. Using both outputs for control output allows for both heating and cooling control or

two stage heating or two stage cooling control. There are four types of control modes: PID,

ON/OFF, RAMP/SOAK and Manual. SOLO Modular can accept various types of thermocouple

and RTDs as well as 0-10V or 4-20 mA anaolog input signals.

Other features include:

• Auto Tuning (AT) function with PID control

• DIN rail mountable

• LEDs for indication and diagnostics

• Easy configuration using SL-SOFT SOLO configuration software or Modbus

communications

• Selectable between °C and °F

• cULus and CE agency approvals

Specifications

Operating Voltage

Range

Power Consumption

Rated 24 VDC, Max. 24 W combined, 3W + 3W x number of SLM2 controllers (Max. 7)

Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK

Input Sensors

Linear DC input: 0 ~ 5V, 0 ~ 10V, 0 ~ 20mA, 4 ~ 20mA, 0 ~ 50mV

Sampling Rate

Analog input: 0.15 sec. Thermocouple or platinum RTD: 0.4 sec.

Control Method

Relay: SPST, Max. load 250VAC, 3A resistive load

Voltage pulse: 12VDC, Max. output current: 40mA

Output Types

Current: DC 4 ~ 20mA (Load resistance: < 500Ω)

Analog voltage: 0 ~ 10V (Load resistance: > 1,000Ω)

Control output, alarm output, retransmit output

Output Function

Retransmit output is available only when output 1 is linear voltage or current output.

Alarm

RS-485 communication, 2,400 bps ~ 38,400 bps

Communication

Protocol

Vibration Resistance

10 ~ 55Hz, 10m/s2 for 10mins, each in X, Y and Z direction

Shock Resistance

Max. 300m/s2, 3 times in each 3 axes, 6 directions

Ambient Temperature

Storage Temperature

Altitude

Ambient Humidity

Pollution Degree

Input Sensor

0 ~ 50mV linear voltage input

4 ~ 20mA linear current input

0 ~ 20mA linear current input

0 ~ 10V linear voltage input

0 ~ 5V linear voltage input

Platinum RTD (Pt100)

Platinum RTD (JPt100)

Thermocouple TXK type

Thermocouple U type

Thermocouple L type

Thermocouple B type

Thermocouple S type

Thermocouple R type

Thermocouple N type

Thermocouple E type

Thermocouple T type

Thermocouple J type

Thermocouple K type

Note 1: Install the supplied 249 ohm resistor between terminal #1 and #2 for linear current inputs.

Note 2: Default setting: Pt100 input.

The range of linear input and feedback value is adjustable. Range of input feedback: -999 ~ 9,999. Take 0 ~ 20mA input as

example, -999 refers to 0mA input, and 9,999 refers to 20mA input. If we change the range to 0 ~ 2,000, 0 will refer to 0mA

input, and 2,000 will refer to 20mA input. 1 display scale = 0.01mA.

21.6 to 26.4 VDC

Platinum RTD: Pt100, JPt100

PID, ON/OFF, Ramp / Soak control or Manual

12 alarm modes

Modbus protocol, ASCII/RTU format

0 to 50°C (32 to 122°F)

-20 to +65°C (-4 to 149°F)

2,000m or less

35% ~ 85% RH (non-condensing)

Input

Available Range

0 ~ 50mV

4 ~ 20mA

0 ~ 20mA

0 ~ 10V

0 ~ 5V

-200 ~ 600°C (-328 ~ 1,112°F)

-20 ~ 400°C (-4 ~ 752°F)

-200 ~ 800°C (-328 ~ 1,472°F)

-200 ~ 500°C (-328 ~ 932°F)

-200 ~ 850°C (-328 ~ 1,562°F)

100 ~ 1,800°C (212 ~ 3,272°F)

0 ~ 1,700°C (32 ~ 3,092°F)

-200 ~ 1,300°C (-328 ~ 2,372°F)

0 ~ 600°C (32 ~1,112°F)

-200 ~ 400°C (-328 ~ 752°F)

-100 ~ 1,200°C (-148 ~ 2,192°F)

-200 ~ 1,300°C (-328 ~ 2,372°F)