ADEMCO 5808LST Instrukcje instalacji - Strona 4

Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Alarm dymowy ADEMCO 5808LST. ADEMCO 5808LST 4 stron. Photoelectronic smoke/heat detector with built-in wireless transmitter

Drukuj stronę

MAINTENANCE

NOTE: Before removing the detector, notify the proper authorities that the

smoke detector system is undergoing maintenance and will be tem-

porarily out of service. Disable the zone or system undergoing mainte-

nance to prevent unwanted alarms.

NOTE: Before removing the detector cover, note the position of the thermis-

tors. Make sure the thermistors are not bent over when the housing is

replaced.

1. Remove the detector housing by gently prying the four housing tabs

on the bottom of the base with a small-bladed screwdriver and pull

the housing from the base. Use caution to avoid damaging the

thermistors.

2. Vacuum the screen carefully without removing it.

3. Remove screen assembly, pulling straight out (please see Figure 4).

4. Remove the sensing chamber cover.

5. Clean the sensing chamber by vacuuming or blowing out dust and

particles.

6. Replace the sensing chamber cover, aligning the arrow on the cover

top with the arrow on the printed circuit board.

7. Replace the screen by placing the screen assembly over the sensing

chamber cover and twisting until it snaps into place.

8. Replace the housing by aligning the two triangular slots on the

base with their counterparts on the housing. Gently press the

housing until it locks in place. Check to make sure that the ther-

mistors are in the upright position.

9. Reinstall the detector.

10. Notify the proper authorities that the system is back in operation.

Please refer to insert for the Limitations of Fire Alarm Systems

Smoke detectors shall be replaced after being in service for 10 years. However, any smoke detector, fire alarm equipment, or any component of that system which

fails prior to that shall be repaired or replaced as soon as possible. Batteries shall be replaced upon indication of a pre-low battery condition.

Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its

product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for

24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer's date stamp, for 12 months from date of original purchase

unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing

or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller's specifications or proves defective

in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered

or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product(s) transportation prepaid, to Honeywell

Factory Service, 165 Eileen Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH

EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY

WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury or property loss

by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer understands that a properly installed

and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it is not insurance or

a guarantee that such will not occur or that there will be no personal injury or property loss as a result.

CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT

THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR

DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL

NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST

SELLER.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase or alteration, written or verbal, of the

obligations of this Limited Warranty is authorized.

AD300-00-00

LIMITED WARRANTY

FCC ID: CFS8DL5808LP-1

FCC PART 15 STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

CANADA: 573F-5808LP1

Figure 4. Removal of Cover and Screen for Cleaning

REMOVABLE

HOUSING

REMOVABLE

SCREEN

SENSING

CHAMBER COVER

SENSING

CHAMBER

BASE

S0163-00

I56-918-14R