Hifonics ZeusZxi 8008 Podręcznik użytkownika - Strona 7
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Wzmacniacz Hifonics ZeusZxi 8008. Hifonics ZeusZxi 8008 15 stron. Zeus 25th anniversary edition high performance amplifier
Drukuj stronę
- 1. Table of Contents
- 2. General Installation Procedure
- 3. Amplifier Feature Descriptions
- 4. Zxi6008 / Zxi1008 / Zxi1308 2 CHANNEL AMPLIFIER APPLICATIONS
- 5. Zxi4408 / Zxi6408 / Zxi8808 4 CHANNEL AMPLIFIER APPLICATIONS
- 6. Zxi8408 5 CHANNEL AMPLIFIER APPLICATIONS
- 6. Channel Discrete, One Being Mono Low Pass / 3 or 4 Channel Discrete, One Being Mono Low Pass / 3 Way Active
- 6. Front/Rear High Pass, with Constant Sub Bass
- 7. Setting up Systems after Installation for Best Performance
- 8. Troubleshooting and Diagnostics
- 9. Features and Specifications
- 10. Product Warranty
ZXi4408 / ZXi6408 / ZXi8408 4 CHANNEL AMPLIFIER APPLICATIONS
2 way active, or bi-amplified system with mono bass
This application shows how easily a 2 way active system can be implemented using
a Zeus 4 channel amplifier. Channels 1 and 2 will be used for highs, and channels 3
and 4 for mono bass.
Interconnect cable checklist:
- We need to feed the same signal to both sets of channels, so must use 2 Y-adapters,
one to feed the LEFT signal to channels 1 and 3, and the right signal to channels 2
and 4, as shown.
Mono bass woofer wiring:
- Connect the mono speaker positive terminal to the LEFT +, and its negative
terminal to RIGHT -.
Switch setting checklist:
- 1/2CH X-OVER: HI
- 3/4CH X-OVER: LP/BP
Crossover frequency control checklist:
Channels 1/2:
- HI PASS: 100 Hz
- LOW PASS: N/A
LEFT TO CHANNELS 1 AND 3
RIGHT TO CHANNELS 2 AND 4
B O O S T
H F R - 3
MI N MA X X
2 way active, or bi-amplified system with mono bass, and faded highs/lows
Here we present a variation of the previous system. Since this is a 2 way system, we
can use the front outputs from a head unit to drive the highs, and the rear output to
drive the bass This method allows the listener to easily adjust the relative levels of
bass to highs, with the front to rear fade on the head unit.
Channels 1 and 2 will be used for highs, and channels 3 and 4 for mono bass.
FULL RANGE
STEREO LINE
INPUTS
B O O S T
H F R - 3
MI N MA X X
Channels 3/4:
- HI PASS (subsonic): 20 Hz
- LOW PASS: 100 Hz
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section "Setting up systems after
installation for best performance"
Level control checklist:
Refer to the section "Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
- 2 ohm per channel in stereo mode.
- 4 ohm mono bridged.
Interconnect cable checklist:
- Use good quality RCA leads to connect the inputs of the amplifier to the source as
shown.
- Follow the instructions as per the previous system for switch and crossover
settings.
MONO
BASS
SPEAKER
STEREO HIGH
SPEAKERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
MONO
OR SUB BASS
SPEAKER
STEREO
FULL RANGE
OR HIGHS
SPEAKERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
5