KitchenAid KEBS107SSS04 Arkusz techniczny - Strona 3
Przeglądaj online lub pobierz pdf Arkusz techniczny dla Piekarnik KitchenAid KEBS107SSS04. KitchenAid KEBS107SSS04 12 stron. 7" (68.6 cm) and 30" (76.2 cm) electric single and double built-in oven
Również dla KitchenAid KEBS107SSS04: Lista części (7 strony), Instrukcja instalacji (16 strony)
Drukuj stronę
FAILURE (Leftmost
ERROR (Rightmost
2 Clock Digits)
2 Clock Digits)
F2
E0
Keypad
E1
SUGGESTED CORRECTIVE ACTION PROCEDURE
PROCEDURE: Before proceeding, perform steps 1 through 3 of "To
Enter Diagnostics Mode."
1.
Unplug oven or disconnect power.
2.
Check that the keypad is firmly connected.
3.
Replace all parts and panels before operating.
4.
Plug in oven or reconnect power.
5.
Observe for longer than 1 minute.
6.
If error remains, then go to Step 7.
7.
Unplug oven or disconnect power.
8.
Replace keypad.
9.
Replace all parts and panels before operating.
10. Plug in oven or reconnect power.
11. Observe for longer than 1 minute.
12. If error remains, then go to Step 13.
13. Unplug oven or disconnect power.
14. Replace cable between user interface and keypad.
15. Replace all parts and panels before operating.
16. Plug in oven or reconnect power.
17. Observe for longer than 1 minute.
18. If error remains, go to Step 19.
19. Unplug oven or disconnect power.
20. Replace oven user interface.
21. Replace all parts and panels before operating.
22. Plug in oven or reconnect power. Wait for 1 minute.
23. Verify operation is normal. Enter into Diagnostics mode by pressing
OFF > OFF > START and complete checks.
LIKELY FAILURE
FAILURE (Leftmost
CONDITION
2 Clock Digits)
Keypad disconnected
F3
Sensors
Stuck key/Shorted key
SUGGESTED CORRECTIVE ACTION PROCEDURE
PROCEDURE: Before proceeding, perform steps 1 through 3 of "To
Enter Diagnostics Mode."
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Ensure all wiring connections are made.
11. Replace all parts and panels before operating.
12. Plug in oven or reconnect power.
13. Observe for longer than 1 minute.
14. Enter into Diagnostics mode by pressing OFF > OFF > START and
F3
Sensors
PROCEDURE: Oven is not equipped with this feature. If error occurs,
before proceeding press OFF, OFF, START to enter into Diagnostics
mode and verify the error codes. If error code returns, replace user
interface with correct control associated with this product.
3
ERROR (Rightmost
2 Clock Digits)
EO
E3
Verify in Diagnostics temperature reading on sensor.
If dashes appear in main temperature display, proceed to Step 3.
Unplug oven or disconnect power.
Remove back panels and ensure the indicated temperature sensor is
plugged in properly and fully inserted.
If it is not, plug it in to the connector and go to Step 11.
If it is plugged in, go to Step 5.
Check connector P2 on the appliance manager. Make sure it is
plugged in and fully seated.
If it is not, make the proper connection and go to Step 11.
If it is already properly connected, go to Step 6.
Visually inspect the wires between P2 on the appliance manager and
the indicated temperature sensor. Make sure the wires are not cut or
pinched. If the wires appear to be intact, unplug the P2 connector on
the appliance manager. Go to Step 7.
Measure indicated temperature sensor resistance value (measure
between appropriate P2 connector pins). For the following sensors,
the resistance value should read:
Main Oven Sensor - Between 931 and 2869 Ω. (Approx. 1080Ω at
room temp.)
Meat Probe Sensor - Between 1,300 and 103,000 Ω. (Approx.
59,000Ω at room temp.) (Insert meat probe into meat probe jack
located inside the oven cavity prior to reading resistance.)
Measure any P2 connector pin to chassis. Resistance value should
read "open." If it does not, replace sensor harness. Repeat Step 7.
If the indicated temperature sensor does not meet these
requirements, go to Step 8.
If the temperature sensor does meet the requirements, go to
Step 11.
For MAIN sensor:
Replace appropriate temperature sensor. Repeat Step 7.
If the requirements are not met, replace sensor harness. Repeat
Step 7.
If the requirements are still not met, go to Step 9.
For MEAT PROBE sensor:
Replace meat probe sensor. Repeat Step 7.
If the requirements are not met, replace sensor harness. Repeat
Step 7.
If the requirements are still not met, replace the meat probe
jack. Repeat Step 7.
If the meat probe sensor is still not meeting the requirements,
go to Step 9.
Replace the appliance manager. Ensure all connectors are properly
seated.
read sensor for main oven sensor and meat probe on immediate
display.
E1
E2
LIKELY FAILURE
CONDITION
Main sensor open or
shorted
Meat probe shorted
Lower main oven
sensor open or shorted
Warming drawer
sensor shorted