Aquasana EQ-10000 Instrukcje instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcje instalacji dla Systemy filtracji wody Aquasana EQ-10000. Aquasana EQ-10000 4 stron. Whole house water filter
Drukuj stronę
Installation Notes
• Read all precautions, installation and operating instructions carefully and completely before
installing the unit.
• Ensure all installation pieces are present prior to beginning.
• Lay out system in appropriate configuration. Improper sequence of equipment will affect
performance, and could possibly damage your system.
• Anticipate the addition of pex tubing, clamps and mounting screws to install unit properly
(available at your local home improvement store or through your plumbing contractor).
Due to the varieties of home design, not all configurations can be addressed in this guide.
Components and time of installation will vary. Please refer your plumbing professional to our
Installation Guide.
• Pick an appropriate installation location. Dimensions of systems vary—always allow an
estimated minimum of 50" clearance for height of tank, and a minimum of 30" for floor space.
Your plumber will be installing the system in an area where the main water line enters your
home, prior to your water heater.
• Do not install the unit on its side or in direct sunlight. Outdoor installation requires the use
of sunproof sumps. Please contact our sales and service department 866-662-6885 to discuss
the specifics of your installation.
• Full warranty contingent on installation by a licensed plumber.
• Do not install this filter where the line pressure may exceed 100 psi. Operating pressure
range: 20psi – 100psi.
• Install on cold water lines only (40° – 90°F). Protect unit from freezing.
• Installation of the filter must comply with existing state and local plumbing codes.
Aquasana is not liable for consequential or incidental damages due to improper installation.
Specifications
Model: EQ-1000
Replacement cartridges
Main tanks: EQ-1000R
Pre-filter: EQ-304-20
Post-filter: EQ-PFC.35
4
Rated service flow: 7 gpm
Max working pressure: 20-100 psi
Max operating temperature: 40° – 90° F
Max capacity: 1,000,000 gal
Use and Care
Customization options are available to address any specific concerns you may have. The best
way to establish your specific needs is to conduct a water test. Contact us by phone:
855-837-7172 or online: www.aquasanamontreal.com.
Component one: Sediment Pre-filter
• Sediment levels vary from one location to another. During the first year of use, a visual
inspection monthly is recommended. The sediment pre-filter is white when you initially
install it. Once you can no longer see white, it is time to replace the filter with a new
one. Allowing sediment to continue to collect can cause clogging and prevent the flow of
water into your home.
Component two: Rhino 2 stage Whole House filter
• This filter unit has a capacity of 1,000,000 gallons. You replace the unit in its entirety every
1,000,000 gallons. Check with your plumber at the time of installation about adding a meter
to your system. Typically, the average family of four will consume that amount in 8-10 years.
Unions are located on each side of the tank for ease of replacement. It is not necessary to
contract a plumber. The replacement part number is EQ-1000R.
Component three: Post-filter
• The post-filter, utilized to remove particulates up to 60 times smaller than the eye can see,
should be replaced every nine months. An added benefit is that any cysts (such as giardia or
cryptosporidium) will also be captured.
Cleaning your system
• The exterior of your filtration system can be cleaned with warm, soapy water. Rinse well
with fresh, clean water. Never use chemical cleaning products on the filters exterior surface
because they may damage the filter housing.
do not use with water that is microbiologically unsafe or of
unknown water quality without adequate disinfection before
or after the system. systems certified for cyst reduction may be
used on disinfected water that may contain filterable cysts.
5