Alphalux SureScan ALXPIR Instrukcje

Przeglądaj online lub pobierz pdf Instrukcje dla Akcesoria Alphalux SureScan ALXPIR. Alphalux SureScan ALXPIR 4 stron. 10a, 240v, 10 metre range

Drukuj stronę

TROUBLE SHOOTING GUIDE:

Problem

Probable Cause

Lights will not activate when there is

Power failure or power not switched on

movement in the detection area

Faulty globe/s

Controls incorrectly set

Sensor aimed incorrectly

Incorrectly wired

Light turns on for no apparent reason

Air conditioner or heater

vents close to sensor

Animals or birds crossing detection area

Reflective objects in detection area

Electrical interference on the same

circuit

Lights will not turn off after set time has

Lights are in manual mode not

elapsed

automatic

Wiring is not correct

The warranty for this electrical product covers defects of materials and workmanship for one year from the date of

purchase, provided that the product is used according to The L&H Group recommendation and is within the limits

specified. The L&H Group will at its own option make good, replace or provide credit for any product manufactured

or supplied by it, which proves to be defective within the limits set out above provided that no repairs, alterations or

modifications to the product have been undertaken or attempted,other than by the company or its authorised agents.

Any defective product should be returned to your original place of purchase or sent Postage Paid to The L&H Group

at the address shown below. The purchase receipt must be returned with the product to obtain warranty repair or

replacement. This warranty is in addition to any guarantee implied by Federal or State legislation.

PROOF OF PURCHASE

• Please retain your purchase receipt for all service or warranty claims.

• Complete details of your purchase in the section below for your own reference.

Date of purchase

Type of Product / Model No

Your Name

Your Address

Branch

Distributed by:

L&H Group

456 Lower Heidelberg Road

Heidelberg VIC 3084

The L&H Group has a policy of continual improvement throughout their product range,

the unit contained may differ slightly from the unit illustrated on the pack.

For product enquiries contact our Customer Service Centre: 1300 300 254

Form No: 4508/MKT 03/11 R

Suggested Solution

Check connections, fuse and switches

Replace globe/s

Change direction angle, adjust

sensitivity

Change position and/or direction of

sensor

Re-check all wiring

Change position and/or direction of

sensor

Probably unavoidable.

Change direction of sensor, adjust

sensitivity

Change direction of sensor and

consider repositioning

Check for arcing switches and replace

noisy fluorescent tubes and/or starters.

Consider connecting the unit to an

alternative circuit

Turn lights off for at least 10 seconds

then turn them on again to return

sensor to automatic mode

Recheck the wiring

Instructions for Alphalux SureScan™ Sensor

Part Number: ALXPIR

10A, 240V, 10 Metre Range

INTRODUCTION:

The Alphalux range of sensors and floodlights that includes the SureScan™ have been designed in

consultation with our customer base of installers. More than 15 years of experience in light fittings and

sensors have combined to create a comprehensive range of high quality solutions.

The Alphalux SureScan™ includes the following features:

• Maximum 10 Amp high power output to control multiple loads.

• High quality passive infrared (PIR) sensing circuit used to prevent nuisance switching.

• Timer, light adjustment and distance sensitivity controls.

• Full sensor head direction adjustment.

• Screw mount lock nut to prevent post-installation movement.

• Three mounting base entry ports for flexible sensor head positioning.

• 20mm threaded mounting base suits common conduit and fitting entries.

• O-ring sealed to maintain IP rating and exclude water and dust.

• Unit base fits typical mounting boxes with 84mm mounting centres.

• Rubber seals supplied for fixing to flat mounting surfaces.

• Includes insulated connectors for faster and more convenient installation.

• Heavy-duty UV stabilised plastic.

• Includes matching mounting box for additional termination space and easy fitment.

INSTALLATION:

Note: This product must be installed by a qualified electrician and in accordance with the appropriate

wiring rules and regulations.

Ensure that all electrical supplies are isolated at the switchboard before installation or maintenance of

these fittings takes place.

FINDING THE BEST LOCATION:

The position of passive infrared sensors (PIR) is critical to their performance and vital in reducing

nuisance triggering. The following guidelines should be followed to maximize the performance of the

units:

• The unit should be a minimum of 2.4 metres above the area that is being monitored.

• For best performance the path of motion should be across the field of vision of the sensor.

Head-on detection is the most unreliable method of sensing.(Refer to diagram)

• To avoid incorrect tripping of sensor, do not mount close to electrical devices which produce

electrical interference (RFI noise). Avoid fluorescent fittings, ceiling fans, remote control doors etc.

Older versions of these devices in particular.