Toshiba 22SKV Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Klimatyzator Toshiba 22SKV. Toshiba 22SKV 12 stron.

• Before installation, please read these precautions for safety carefully.

• Be sure to follow the precautions provided here to avoid safety risks. The symbols and their meanings are shown below.

WARNING : It indicates that incorrect use of this unit may cause severe injury or death.

CAUTION : It indicates that incorrect use of this unit may cause personal injury (*1), or property damage (*2).

*1: Personal injury means a slight accident, burn, or electrical shock which does not require admission or repeated hospital treatment.

*2: Property damage means greater damage which affects assets or resources.

Power supply cord of parts of appliance for outdoor use shall be at least polychloroprene sheathed ﬂ exible cord (design H07RN-F) or cord designation

60245 IEC66 (1.5 mm

or more). (Shall be installed in accordance with national wiring regulations.)

CAUTION

•

THIS AIR CONDITIONER USES THE NEW HFC REFRIGERANT (R410A), WHICH DOES NOT DESTROY THE OZONE LAYER.

R410A refrigerant is apt to be affected by impurities such as water, oxidizing membranes, and oils because the pressure of R410A refrigerant is approx.

1.6 times of refrigerant R22. As well as the adoption of this new refrigerant, refrigerating machine oil has also been changed. Therefore, during installation

work, be sure that water, dust, former refrigerant, or refrigerating machine oil does not enter the refrigeration cycle of a new-refrigerant air conditioner.

To avoid mixing refrigerant and refrigerating machine oil, the sizes of charging port connecting sections on the main unit are different from those for the

conventional refrigerant, and different size tools are also required. For connecting pipes, use new and clean piping materials with highpressure withstand

capabilities, designed for R410A only, and ensure that water or dust does not enter. Moreover, do not use any existing piping as its pressure withstand

may be insufﬁ cient and may contain impurities.

DANGER

• FOR USE BY QUALIFIED PERSONS ONLY.

• TURN OFF MAIN POWER SUPPLY BEFORE ATTEMPTING ANY ELECTRICAL WORK. MAKE SURE ALL POWER SWITCHES ARE OFF.

FAILURE TO DO SO MAY CAUSE ELECTRIC SHOCK.

• CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED WRONGLY, ELECTRIC PARTS MAY BE

DAMAGED.

• CHECK THE EARTH WIRE THAT IT IS NOT BROKEN OR DISCONNECTED BEFORE INSTALLATION.

• DO NOT INSTALL NEAR CONCENTRATIONS OF COMBUSTIBLE GAS OR GAS VAPORS.

FAILURE TO FOLLOW THIS INSTRUCTION CAN RESULT IN FIRE OR EXPLOSION.

• TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE HAZARD, PLACE THE UNIT WELL AWAY (MORE THAN 2 M) FROM HEAT

SOURCES SUCH AS RADIATORS, HEATERS, FURNACE, STOVES, ETC.

• WHEN MOVING THE AIR CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY CAREFUL NOT TO GET THE SPECIFIED

REFRIGERANT (R410A) WITH ANY OTHER GASEOUS BODY INTO THE REFRIGERATION CYCLE. IF AIR OR ANY OTHER GAS IS MIXED IN THE

REFRIGERANT, THE GAS PRESSURE IN THE REFRIGERATION CYCLE BECOMES ABNORMALLY HIGH AND IT RESULTINGLY CAUSES BURST

OF THE PIPE AND INJURIES ON PERSONS.

• IN THE EVENT THAT THE REFRIGERANT GAS LEAKS OUT OF THE PIPE DURING THE INSTALLATION WORK, IMMEDIATELY LET FRESH AIR

INTO THE ROOM. IF THE REFRIGERANT GAS IS HEATED BY FIRE OR SOMETHING ELSE, IT CAUSES GENERATION OF POISONOUS GAS.

WARNING

• Never modify this unit by removing any of the safety guards or bypassing any of the safety interlock switches.

• Installation work must be requested from the supplying retail dealership or professional vendors. Self-installation may cause water leakage, electrical

shock, or ﬁ re as a result of improper installation.

• Speciﬁ ed tools and pipe parts for model R410A are required, and installation work must be done in accordance with the manual. HFC type refrigerant

R410A has 1.6 times more pressure than that of conventional refrigerant (R22). Use the speciﬁ ed pipe parts, and ensure correct installation, otherwise

damage and/or injury may be caused. At the same time, water leakage, electrical shock, and ﬁ re may occur.

• Be sure to install the unit in a place which can sufﬁ ciently bear its weight. If the load bearing of the unit is not enough, or installation of the unit is

improper, the unit may fall and result in injury.

• Electrical work must be performed by a qualiﬁ ed electrical engineer in accordance with the code governing such installation work, internal wiring

regulations, and the manual. A dedicated circuit and the rated voltage must be used. Insufﬁ cient power supply or improper installation may cause

electrical shock or ﬁ re.

• Use a cabtyre cable to connect wires in the indoor/outdoor units. Midway connection, stranded wire, and single-wire connections are not allowed.

Improper connection or ﬁ xing may cause a ﬁ re.

• Wiring between the indoor unit and outdoor units must be well shaped so that the cover can be ﬁ rmly placed. Improper cover installation may cause

increased heat, ﬁ re, or electrical shock at the terminal area.

• Be sure to use only approved accessories or the speciﬁ ed parts. Failure to do so may cause the unit to fall, water leakage, ﬁ re or electrical shock.

• After the installation work, ensure that there is no leakage of refrigerant gas. If the refrigerant gas leaks out of the pipe into the room and is heated by

ﬁ re or something else from a fanheater, stove or gas range, it causes generation of poisonous gas.

• Make sure the equipment is properly earthed. Do not connect the earth wire to a gas pipe, water pipe, lightning conductor, or telephone earth wire.

Improper earth work may be the cause of electrical shock.

• Do not install the unit where ﬂ ammable gas may leak. If there is any gas leakage or accumulation around the unit, it can cause a ﬁ re.

• Do not select a location for installation where there may be excessive water or humidity, such as a bathroom. Deterioration of insulation may cause

electrical shock or ﬁ re.

• Installation work must be performed following the instructions in this installation manual. Improper installation may cause water leakage, electrical shock

or ﬁ re. Check the following items before operating the unit.

- Be sure that the pipe connection is well placed and there are no leaks.

- Check that the service valve is open. If the service valve is closed, it may cause overpressure and result in compressor damage. At the same time, if

there is a leak in the connection part, it may cause air suction and overpressure, resulting in damage to the unit or injury.

• In a pump-down operation, be sure to stop the compressor unit before removing the refrigerant pipe. If removing the refrigerant pipe while the

compressor is operating with the service valve opened, it may cause air suction and overpressure, resulting in damage to the unit or injury.

• Do not modify the power cable, connect the cable midway, or use a multiple outlet extension cable. Doing so may cause contact failure, insulation

failure, or excess current, resulting in ﬁ re or electrical shock.

• If you detect any damage, do not install the unit. Contact your supplying dealer immediately.

1110651154-EN.indd 1

PRECAUTIONS FOR SAFETY

For general public use

New refrigerant air conditioner installation

2/15/10 9:39:36 AM