Pioneer DEH-P5450 Instrukcja obsługi - Strona 17

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odtwarzacz CD Pioneer DEH-P5450. Pioneer DEH-P5450 19 stron. Multi-cd control high power cd player with fm/am tuner
Również dla Pioneer DEH-P5450: Instrukcja instalacji (6 strony), Instrukcja obsługi (19 strony)

Pioneer DEH-P5450 Instrukcja obsługi
Section
Setting the FM tuning step
Tre tun:ng steo employes by Seek Turing ir the
PM mode car be switched between 100 KHz
'greset at the factory! ard 50 kI1z.
1 Press FUNCTION to select FM STEP.
Prass FUNCTION 'cpeatecl; uot: FM STEP
apoears
nthe display.
2 Select the FM tuning step with </>.
Note
* If see tuning is performed 17 0 «Hz steps.
stations may oe tuned in imprecisely. Ture in
the stat.ons with manual turing or use seek
turirg again. @
Setting the AM tuning step
The AM tuning step can be switcred vetween 9
«Hz, the preset step, and 10 kHz, When Lsing
the tuner ir North, Central or South America.
reset the tuning step from 9 kHz (531 — 1.602
kHz allowable) to 10 kHz {830
- 1.640 «rz a low-
able}.
1
Press FUNCTION to select AM STEP.
Press FUNCTION
receatedly urtil AM STEP
appears ir the d'splay.
2 Select the AM tuning step with </>.
Pressirg <@/m wil switcn tne AM tuning step
between & «Hz and "9 kHz. The selected AM
tuning steo will agpear in tre display.
Switching the warning tone
i the front care: is rot detacnesc trom tig heas
unit within fve seconds of turring off the igri-
ton. a warring tone wii scurd. You can turn off
t1-s warning tone.
1 Press FUNCTION to select WARN.
Press FUNCTION reseatedly unz | WARN
aprears inthe disp-ay.
2 Select WARN on or off with a/v.
Pressing a/¥ wil switch WARN between cr
ana ott ano that status wil. be displayed (e.g.
WARN :ON)
[#/
Switching the auxiliary setting
It is possible to use auxiliary equ pment with
tris une. Activate the auxliary setting when
using external equiprren: connected te this
unit,
1
Press FUNCTION to select AUX.
Press FUNCTION repeatedly unt.| AUX appears
iv tne display.
'
2 Select AUX on or off with a/v.
?ressing a/W wll switch AUX betwee on ane
off and that status will be d spiayed (e.g..
AUX:ON), =
Initial Settings
Switching the dimmer setting
Tc prevers: tne d:splay from being too bright at
right. the disolay is automatical'y dimmed
when the car's headlights are turned on. You
car switch dimmer on or off,
1
Press FUNCTION to select DIMMER.
Press FUNCTION repeatedly uni] DIMMER
appears in the display,
2
Select DIMMER on or off with a/v.
~ -
Pressing a/¥ will switch DIMMER between or:
and oft ard that status will be displayed (e.g..
DIMMER :ON). [#|
Section
Switching the rear output setting
a=
This unit's rear output (rear speaker leads out-
out and RCA rear output) can be used for full-
range speaker or suowoofer connection. If you
switch the rear output setting to the subwoofer.
yOu Can connect a rear speaker lead d:rectly to a
subwoofer without using an auxiliary amp.
* If you connect a subwoofer to the rear output.
set the output setting to subwoofer.
* Even if you change this setting. there is no
output uniess you switch the subwoofer output
on (refer to Using subwoofer output or page 29).
* Both rear speaker leads output and RCA rear
output are switched simultaneously in this set-
tng.
1 Press FUNCTION to select the rear output
setting mode.
Press FUNCTION repeatedly until FRT+REAR
appears in the display.
* If tne rear output setting has been set to the
Subwoofer then FRT+S/W wil: be aisplayed.
2 Select full-range speaker or subwoofer
with </>,
Pressing </ wi:i switch betweer FRT+REAR
(full-rarge speaker} and FRT+S/W (subwoofer!
and that status will be disp'ayed. =
m
3
=
an
=