Ariston MARGHERITA Instrukcja instalacji i użytkowania - Strona 20

Przeglądaj online lub pobierz pdf Instrukcja instalacji i użytkowania dla Spryskiwacz Ariston MARGHERITA. Ariston MARGHERITA 32 stron.
Również dla Ariston MARGHERITA: Instrukcja instalacji i użytkowania (32 strony), Instrukcja instalacji i użytkowania (16 strony)

Drukuj stronę

ARGHERITA

Here Im in command

Making the right choice is important. And its easy.

Programme selector knob

To select a programme, you should

turn the knob so that the symbol/

number of the desired programme is

in line with the pointer on the glass G.

On-off

When button B is pressed, the

washer-dryer is switched on, when

it is not the machine is switched off.

Turning the appliance off

does not cancel the selected

programme.

When the appliance is switched on,

all the symbols on the display light

up for at least 8 seconds, after

which only the ones that can be

selected will flash.

Start /Reset

This button allows you to start the

selected wash programme or to

interrupt it.

If you press it briefly, the button

functions as Start, if you press it

for at least 3 seconds, then it

functions as Reset.

After the Start of the appliance,

moving the programme selector

knob will have no effect

whatsoever.

Detergent dispenser

It is divided into three

compartments:

1. Detergent for pre-wash;

2. Detergent for the main cycle wash;

3. Fabric conditioner.

The washer-dryer is equipped with

an extra compartment 4 (provided

as an accessory) for the bleach, to

be inserted in compartment 1.

Programme key

This contains the descriptions of the

wash programmes and the various

functions connected to the buttons.

Pull it outwards to open it.

Display

All the options available are

displayed on the right-hand side.

Use the Mode button to select the

desired option, and the relative

symbol will begin flashing.

The detergent dispenser with

the additional bleach

compartment is here.

Margherita - Instructions for installation and use

Margheritas knobs

are hidden. Just

press them lightly in

the middle to

extract them.

Mode

Select

On the left-hand side, the value or

the status (On-Off) of the selected

option is displayed, and you can

modify it using the Select button.

To access the subsequent option,

press the Mode button, otherwise

press button C (Start/Reset) to start

the wash cycle.

All the options available are listed

below.

Only options relevant to the

selected programme will be

displayed.

Temperature

The display indicates the maximum

temperature relating to the

programme set, which can be

reduced by pressing the Select

button right down to cold wash (Off).

This option is available on all wash

programmes.

Spin variation

The display indicates the maximum

speed relating to the programme set,

which can be reduced by pressing the

Select button right down to its total

exclusion (Off).

You may not select a drying

cycle if you have excluded the

spin cycle.

During a wash cycle, the selection

of the spin cycle exclusion is

indicated by symbol

coming on.

Understanding the control panel

This option is available on all wash

programmes except for number 10

and Drain.

Wash intensity

This allows you to modify the

characteristics of the selected wash

programme, according to how soiled

the washing is. There are three levels;

press the select button to Select

them.

Low

Medium

High

This option is available on

programmes 1-2-3-5-6-7.

Delay timer

This allows you to delay the start of

the wash cycle by a minimum of 1

to a maximum of 24 hours by

pressing the Select button.

The enabling of the delayed start is

indicated by the symbol

coming

on and staying on until the wash

cycle begins.

This option is not available on the

Drain and Light Spin programmes.

Stain removal

(see page 21)

Thanks to this command, the washer-

dryer will carry out a more intensive

wash that optimises the effectiveness

of the liquid additives, thus allowing

more resistant stains to be removed.

To use this, press the Select button

until the On sign comes on.

During a wash cycle, the selectionof

this option is indicated by symbol

coming on.

This option is available on

programmes 2-3-5-6-7-9 and Light

Rinse.

Note: It must not be used with the

Easy iron option.

Easy iron

This function allows your washing

to come out of the machine without

creases, making it much easier to

iron.

The appliance optimises the

washing conditions according to the

type of fabrics that are being

washed.

It is enabled with programmes 3-5-

6-7-10 and Light Rinse.

To enable it, press the Select button

until the On sign comes on.

In programmes 6-7-10 and Light

Rinse, the wash cycle is

interrupted and the washing is left

to soak in water before the

appliance is drained. To complete

the cycle, press the Select button.

During a wash cycle, the enabling

of this option is indicated by symbol

coming on.

Note:

- It must not be used with the Stain

removal option.

- If you also want to run the drying

cycle, this button is enabled only

if combined with level

(Iron).

Rinse level

This increases the efficiency of the

rinse. We recommend that you use

it when dealing with a full load and

a great amount of detergent.

There are three levels; press the

Select button to select them.

Low

Medium

High

This option is available on

programmes 1-2-3-4-5-6-7 and

Light Rinse.

Drying

This allows you to set the automatic

drying at the end of the wash.

For further details, please refer to

page 19.

Warning: If you set "spin cycle

exclusion", you may not select a

drying cycle.

If you wish to run a drying cycle,

select the maximum spin speed

available and then choose the type

of drying required.