alphatronics AlphaVision CP 508 Podręcznik użytkownika - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Panel sterowania alphatronics AlphaVision CP 508. alphatronics AlphaVision CP 508 6 stron.

Drukuj stronę

1. OPERATIONS

The CP-508 control panel can be operated by one or more keypads. When keypads are used an

identification code is required. This code is called PIN-code. All PIN-codes are 4-digit codes. There

is one 2-digit code available by which a quick arming procedure can be performed. PIN-codes can be

devided into 3 levels:

systemsupervisor

sectionleader

user

After entering a valid 4-digit PIN-code, on the display the indication 'oP' will appear. Is the entered

code invalid then on the display the indication 'FC' will appear for about 3 seconds.

The CP-508 control panel can be armed and disarmed also by using keyswitches.

1.1 Keypad

The meaning of the horizontal dashes of the leftmost digit is as follows:

uppermost on: section A armed

uppermost off: section A disarmed

middle on:

middle off:

lowest on:

lowest off:

The horizontal dashes of the rightmost digit have

following meaning:

uppermost on: one or more zones belonging to secti-

on A are isolated

middle on: one or more zones belonging to section B

are isolated

lowest on: one or more zones belonging to section C

are isolated

1.1 a) The LED's 1 to10 indicate if a zone is clo-

sed or opened. If the LED is flashing then

the zone is currently opened. Which zone is

indicated by which LED depends on the sta-

tus of the rightmost point in the display (see 1.1c) The OFF LED (green) is turned on if all

sections are disarmed. If one or more sections are armed then the ARM LED will be turned

on. If the ARM LED is flashing, then the control panel is switched into the HOME situation.

1.1 b) The point in the middle of the display is used as mains indication. If mains is present, it will

be turned on, if not present then it starts flashing. If the programmed delay time is over then

the point will be turned off

1.1 c) The rightmost point in the dis-

play indicates which group of

zones is displayed by the LED's

1 to 10. If the point is turned

off, then LED's 1 to 9 indicate

the status of zones 1 to 9, other-

wise zones 10 to 16 are shown

by the LED's 10 and 1 to 6.

2. ARMING THE CONTROL PA-

NEL

2.1 Control Panel arming completely

Enter PIN-code. Press <#>-key. All sec-

tions where the entered PIN-code is aut-

horized for, will be armed. If the 2-digit

quick-arming code is programmed, then

the control panel can be armed by ente-

ring those 2 digits followed by pressing the <#>-key. This 2-digit code can, of course, not be used for

Manual CP-508 versie 2.5

highest priority, allways authorized.

can programm user codes belonging to his section(s) and can arm/disarm

section(s).

can arm/disarm section(s).

section B armed

section B disarmed

section C armed

section C disarmed

M a i n s

in d ic a ti o n

D is pla y

2 -d ig its

M a in s

in d ic a tio n

Z o n e 1 0

o r a b o v e

in d ic a tio n

D i s a r m

D is p la y

2 -d ig its

L E D 1 ,2 ,3

L E D 4 ,5 ,6

Z o n e 1 0

L E D 7 ,8 ,9

o r a b o v e

in d ic a ti o n

L E D 1 0

D is a rm e d

in d ica tio n

September 17th 1993

D is a rm e d

L E D ' s 1 to 1 0

in d ic a tio n

A r m e d /H o m e

in d ic a ti o n

S e c tio n A

S e c ti o n B

S e c tio n C

I s o la te

A r m

S e c ti o n A

S e c ti o n B

S e c ti o n C

D is a rm

A rm

A rm e d/H om e

in d ic a tio n

Is o la te

pg. 2