ARO 50 SERIES Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Silnik ARO 50 SERIES. ARO 50 SERIES 8 stron. Power motor

1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
PART NUMBER
FOR ORDERING
PART NUMBER
FOR ORDERING
33911
46377
47205
46449
46448
46452
41654
46354
46723
46374
46296-2
Yl78-28
46326
47724
46312-l
46454
46413
48201-l
47722
Screen
.............................
Inlet Adapter
........................
Spacer
.............................
Diffuser Washer
.....................
Exhaust Cap
........................
Filler (2 req'd) .......................
Spring ..............................
Valve Rod Assembly
.................
Housing Assembly
...................
Spring ..............................
Throttle Pin .........................
Roll Pin .............................
Lever
..............................
Ball Bearing .........................
Rear End Plate ......................
Rotor ...............................
Blade (5 req'd)
......................
Cylinder
............................
Front End Plate ......................
20
21
22
23
24
26
27
29
30
31
32
34
35
36
Ball Bearing .........................
MOTOR ASSEMBLY (includes items 14 thru 20)
"0" Ring ............................
Spacer
.............................
Locating Pin .........................
Sun Gear 4.4:1 ratio (15 teeth) .........
Planet Gear (3 req'd) 4.4:l ratio (18 teeth)
Needle Bearing (6 req'd) ..............
Carrier Assembly 4.4:1 ratio ...........
Sun Gear (1 or 2 req'd) 3.43:1 ratio (21 teeth) ...
Planet Gear (3 or 6 req'd) 3.43:1 ratio (15 teeth) .
Shaft (3 req'd) .......................
Spindle 3.4: 1 ratio
...................
Ring Gear
..........................
Spacer
.............................
Ball Bearing .........................
Retaining Ring
......................
Carrier Assembly 3.43:1 ratio ..........
Y65-13
48226-1
Y325-214
46412
47723-2
46466
46900
42315
46522
46465
46899
46459
47260-2
46467-l
46496
46243
38339
46521
DISASSEMBLY/ASSEMBLY
INSTRUCTIONS
I NOTlCE
l
Never apply excessive
pressure by a holding device which
may cause distortion of a part.
l
Apply pressure evenly to parts which have a press fit.
l
Apply even pressure to the bearing race that will be press
fitted to the mating part.
l
Use correct tools and fixtures when servicing this tool.
l
Don't damage "0" rings when servicing this tool.
l
Use only genuine ARO replacement
parts for this tool. When
ordering, specify part number, description, tool model number
and serial number.
GEARING
DISASSEMBLY
_
Using a wrench on flats of ring gear (32) and a strap wrench on
housing (9) remove ring gear from tool.
_
Remove retaining ring (35) from spindle.
_
Remove spindles and gears from ring gear. NOTE: Keep
gears grouped with mating spindle when disassembling.
-
Do not remove bearing (34) or spacer (33) unless damage is
evident.
_
To remove bearing (34) and spacer (33) from ring gear, press
on spacer (33) from inside splined end of ring gear.
-
Do not remove gear (28) from carrier assembly unless dam-
age is evident. Gear is press fit onto carrier assembly.
GEARING
ASSEMBLY
_
Assemble spacer (33) into ring gear (32).
-
Lubricate bearing (34) with ARO 33153 grease and assemble
into ring gear, pressing on outer race of bearing.
_
Coat shafts of spindles with ARO 33153 grease.
_
Assemble gears, containing bearings (26) to shafts of mating
spindle.
_
Assemble carrier assembly to spindle.
_
Lubricate
sets of gears liberally
with ARO 33153 grease
(approximately
1/32 oz. per reduction).
_
Assemble spindles and gearing into ring gear. Rotate spindle
and gears to align gear teeth with splines of ring gear.
_
Thread ring gear to tool and tighten with wrench on flats.
MOTOR DISASSEMBLY
_
Remove gearing from tool.
_
Remove spacer (22).
_
Tap front edge of housing to remove motor assembly. Locat-
ing pin (23) should also come out.
Tap drive end of rotor (16) with a soft face hammer; motor will
come apart. NOTE: Bearings are press fit on rotor.
Remove end plate (15) and bearing (14) from rotor.
MOTOR ASSEMBLY
Lubricate bearing (14) with ARO 33153 grease and assemble
to end plate (15) pressing on outer race of bearing.
Assemble end plate (15) to rotor (16) pressing on inner race
of bearing.
Coat five rotor blades (17) with ARO 29665 spindle oil and as-
semble to rotor slots - straight side out.
Coat i.d. of cylinder (18) with ARO 29665 spindle oil and as-
semble over rotor. NOTE: Air inlet slots in end of cylinder must
be aligned with two air inlet holes in end plate (15).
Assemble
bearing (20) to end plate (19), pressing on outer
race of bearing.
Assemble
end plate (19) to rotor, pressing on inner race of
bearing. Be sure rotor turns without binding.
Insert locating pin (23) into ,096" diameter blind hole at bottom
of motor cavity in housing.
Align notches of end plates and cylinder and install motor into
housing, aligning notches with locating pin (23).
Grease and assemble "0" ring (21) to end plate (19).
Assemble spacer (22) to motor.
THROTTLE
DISASSEMBLY
Clamp air inlet adapter (2) in a smooth face vise.
Unthread housing (9) with a strap type wrench.
Remove spacer (3) diffuser washer (4) exhaust cap (5) two fill-
ers (6) spring (7) and valve rod (8). CAUTION: Do not remove or
adjust rubber portion of valve rod (8) as it is preset at the factory.
Remove throttle pin (11) and spring (10).
Remove screen (1) from inlet adapter.
THROTTLE
ASSEMBLY
Install spring (10) and throttle pin (11) into housing, aligning
slot in throttle pin with air inlet holes in housing.
Install valve rod assembly (8) into housing. NOTE: Throttle pin
(11) should not pull out when throttle rod (8) is seated properly.
Install two fillers (6) to exhaust cap (5).
Install exhaust cap (5) to housing, aligning lever (13) with
throttle pin (11).
Assemble spring (7) into housing.
Assemble diffuser washer (4) and spacer (3) to housing, se-
curing with inlet adapter (2).
Clean and replace screen (1) in inlet adapter.
5