Asko 1805 FI Instrukcja instalacji - Strona 12

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Zmywarka Asko 1805 FI. Asko 1805 FI 12 stron.

Drukuj stronę

FITTING

FITTING THE SEMI-INTEGRA

FITTING

THE SEMI-INTEGRA

THE SEMI-INTEGRATED CUST

FITTING

THE SEMI-INTEGRA

P P P P P ANEL ON MODEL 1895

ANEL ON MODEL 1895

Model 1895 was designed to easily accommodate

custom panels. If you use the 4" toe kick, a 2" filler strip

or a pullout cutting board above the unit will be

necessary.

The opening width for Model 1895 is 23-5/8" (600 mm),

which is 3/8" narrower than standard domestic

dishwashers.

ITEMS PRO O O O O VIDED

ITEMS PR

VIDED

ITEMS PR

VIDED

VIDED WITH

Two short screws (D)

Four long screws (E)

Four adhesive-backed plastic spacer washers (D)

One protective tape

INST

INSTALLING

INST

ALLING

ALLING THE P

ALLING

THE PANEL

THE P

Before fitting the custom panel, the dishwasher must

be installed underneath the cabinet. After you've made

the required measurements, pull the machine out again

to install the panel.

Refer to the illustration at right for instruction references.

1. Loosen the screws (A) on the outer edges of the

dishwasher door.

2. Pull the turbo fan exhaust frame (B) down until the

lower edge aligns with the lower edge of the cabinets

and tighten the screws (A). Next, snap the plastic

duct securely into the turbo fan exhaust vent.

WARNING!

The custom panel must not

obstruct the turbo fan exhaust.

See step 2 above for instructions

on how to adjust the fan exhaust.

3. The spacers (C) between the control panel and the

custom door panel allow you to accommodate the height

of the custom panel (from 1" up to 1-7/16"). To remove a

spacer, loosen the nuts at the bottom of the spacers

and remove as many as necessary. Screw the nuts

back on and cut off any protruding parts of the plastic

screws. (If necessary, you can omit the spacers.)

4. To mark where to put the two short screws (E), hold

the custom panel in place against the front of the

dishwasher door and measure 16-1/8" from the top of

the dishwasher, marking that distance on both sides

of the custom panel. Next, measure 5/8" from the edges

and mark that across the first measurement.

5. Insert the short screws (E) into the back of the

wooden panel where you marked, leaving 1/8" of

space between the screw heads and the panel.

6. Insert the screw heads (E) into the lower part of the

keyholes (D) and push the panel upward until the

door aligns with the cabinets.

7. Holding the custom panel in place, open the

dishwasher door and tighten the four screws (F)

that secure the panel.

Page 12

WITH

THE UNIT

WITH THE UNIT

WITH

THE UNIT

ANEL

TED CUST

TED CUSTOM DOOR

TED CUST

OM DOOR

TED CUST

OM DOOR

W W W W W OODEN P

OODEN P

ANEL DIMENSIONS

OODEN P

OODEN PANEL DIMENSIONS

ANEL DIMENSIONS

Width:

23-3/8" (594 mm)

Height:

22-9/16"–24" (573 mm–609 mm)

Thickness:

3/4" (19 mm) (to be flush with the control

panel)

Weight:

Up to 22 lbs.

NOTE: Specifications subject to change without

notice.

NOTE: Heavy-duty door springs can be purchased for

wooden door panels weighing over twelve

pounds. (P/N 8071323-77).

Installing the 1895 Custom Panel

ADJUSTING THE DOOR SPRINGS

After you install the custom

panel, make sure the door can

be opened at any angle. If it

tends to fall down, pull out the

machine and tension the door

springs on the sides of the

machine by moving them one

hole farther back or by twisting

the spring to make it shorter. If

that doesn't resolve the problem, you may need to

purchase the heavy-duty door springs (Part Number

8071323-77).

FASTENING THE DISHWASHER

TO THE CABINET

Refer to page 8.