Astria Rhapsody42TEN Manual de instruções de instalação - Página 4

Procurar online ou descarregar pdf Manual de instruções de instalação para Lareira de interior Astria Rhapsody42TEN. Astria Rhapsody42TEN 10 páginas. 42- and 54-inch linear direct vent gas fireplaces

Control Compartment
Access Panel
and Gasket
Right Burner Bracket
Figure 6: Accessing the control compartment
3. Loosen the front left screw of the right burner bracket.
Remove the other three screws, and rotate the bracket
clockwise to uncover the slot in the firebox floor (Figure 6).
Connect wiring harnesses for blower and optional
firebox liner backlight kit
NOTE: Use only original, factory-supplied wiring inside fireplace.
1. In the control compartment, use a screwdriver or other
blunt object to carefully break the sealant around the wires.
NOTE: Be careful not to damage the wires.
2. Plug the
multiwire
backlight kit) into the SimFlame™ (flicker) module port with
the red wires (Figure 7).
NOTE: If not installing the SimFlame module, plug the
multiwire
harness directly into the power harness (omit the
components outlined in Figure 7) and skip step 3.
Multiwire Harness from
Panel Backlighting Kit
Figure 7: Connecting
3. Plug the power harness (provided with the firebox liner
backlight kit) into the SimFlame Module port with the black
and white wires (Figure 8).
Plug blower
into FAN port
Figure 8: Connecting the lights and blower
4
INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES
Orifice
- PF1 System*
harness (provided with the firebox liner
SimFlame
Module
If not using SimFlame
(flicker) module, omit
outlined components.
multiwire
harness and
flicker
Slot
Multiwire
Harness
AUX
FAN
SimFlame
OUT
Module
Fan Control
Module
Plug lights into
Power
AUX OUT port
Harness
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4. Route the lighting wiring up through the access opening,
and slide it into the slot (Figure 8).
5. Plug the power plug end of the power harness into the AUX
OUT port on the fireplace fan control module (Figure 8).
Install reflector (from optional firebox liner backlight kit)
1. Insert the bottom edge of the reflector (provided with the
firebox backlight kit) into the fireplace first. Then, push the
top edge into rear of fireplace (Figure 9).
NOTE: Lift the reflector over the tabs on the rear ledge of the fireplace
2. Align the large hole in the lower face of the reflector over
the screw in the firebox rear wall.
3. Align the screw holes in the top and bottom edges of reflector
with the rearmost holes in the fireplace ceiling and rear ledge.
Slot
Secure the reflector using six (6) #10-16 x 3/8 hex-head sheet
metal screws provided with the firebox liner backlight kit.
Fireplace
Front
Figure 9: Installing the reflector
Install side panels (from required firebox liner kit)
Power
Harness
1. Align the screw hole in the top flange of the side panel with
the upper hole in the inside wall of the fireplace (Figure 10).
(Plug into
2. Align the screw holes in the bottom flanges of the side
AUX OUT
panel with the holes in the front and rear ledges.
on Control
Module)
3. Secure each panel with three (3) #10-16 x 3/8 hex-head
sheet metal screws provided with the firebox liner kit.
module
Left Side
Panel
Figure 10: Installing the side panels
*For PF2 System, see Page 5 and Figure 7a..
Reflector
Tab
Rear Ledge
~
Left Side
Panel
Right
Side
Panel
Front
Ledge
Rear
Ledge
~