Akw Braddan 16472W Instruções de instalação e cuidados do utilizador

Procurar online ou descarregar pdf Instruções de instalação e cuidados do utilizador para Produto de canalização Akw Braddan 16472W. Akw Braddan 16472W 2 páginas. Shower tray

Imprimir página
Step 3 - Cutting 1800mm Tray to length
See Instructions 07-003-020 for more information on Cut-to-length.
Angle A
Angle B
3
/
"
4.5mm (
)
16
dia. holes
No.8 x 38mm
1
1
/
"
(
)
2
Countersunk
No.8 x 13mm
Screws
1
/
"
(
) Pan Head
2
Screws
The Braddan 1800 tray has a cut to length area that can be cut to suit the dimension between walls down to 1500mm.
Use a fine toothed blade in either jigsaw or handsaw (cut from below with jigsaw or from above with handsaw).
Allow for thickness of trim angle 'B' (2mm or
1
/
") when cutting tray to size (See Fig. 10).
8
After trimming tray and angles A & B to size, mastic underside of tray in position of angle 'B' placement. Fit angle 'B' to
underside of tray with stainless steel screws. Place tray onto a prepared level floor and between walls, ensuring that angle
'B' is tight against end wall. Place angle 'A' onto tray and against angle 'B' then drill 4.5mm (
location through both angles (drill countersunk holes in angle 'A'). Remove angle 'A' then drill through previously drilled holes in
angle 'B' with a No.10 / 5mm masonry drill into wall and fit plastic wall plugs. Silicone seal undersides of angle
'A' then fix to wall with No. 8x38mm (1
1
/
") countersunk head stainless steel screws. Silicone seal between angle 'A' and tray if
2
required. If required the trimmed tray edge is now ready for end moulding. (See cut-to-length instructions 07-003-020).
Step 4 - Braddan Ramps
Fig. 11
Snap in
Flush
Place ramp onto a level floor and
Vinyl Flooring
against tray, ensure ramp is flush
with tray edge and in
appropriate position. Mark off
fixing holes, drill and insert
suitable fixings in the floor.
Fig.12
Apply silicone sealant to contact
area of ramp before fixing with
Silicon Seal
No.8 x 38mm (1
ALL GRP TRAYS
tapping screws. Snap in
plastic sections to close fixing
Label for
cavity and place end caps to ramp
using adhesive. Note: For ramps
that continue around corner of
End Cap
tray, a 45º joining piece is
Fig.13
supplied. These ramps may
45º joining piece
require cutting to size. Ensure
that silicone is applied between
joining piece and tray and joining
piece and ramp.
(See Figs. 11, 12 and 13).
Note
DoP numbers are
Failure to install this AKW product in accordance with supplied instructions or the making of unauthorised modifications will
invalidate any warranty and will affect product safety.
To order additional products or parts please call: 01905 823299 or on the details above
AKW, Pointon Way, Hampton Lovett, Droitwich Spa, WR9 0LR
Tel.+44 (0) 1905 823298 - Fax. +44 (0) 1905 823297 - www.akw-ltd.co.uk
© 2018 AKW
300mm MAX Cut down length
Fig. 10
3
/
") diameter holes on 'v' groove
16
Contact
Technical Help line
01905 560219
Orderline
01905 823299
General Enquiries
01905 823298
Fax
01905 823297
Website
www.akw-ltd.co.uk
1
/
") pan head self
2
Quotes & orders email
Product
Enquiries email
DoP 01-018-330
Packaging
DoP
07-003-050
Manual
AKW Limited
Pointon Way, Hampton Lovett
Droitwich Spa, WR9 0LR
United Kingdom
www.akw-ltd.co.uk
DoP 01-018-330-02
DoP
07-003-050-02
Braddan
Tri-form
09-012-075
GRP Braddan
01-018-330
Sulby
01-018-331
Sulby 2
01-018-332
Multi Spec
01-018-333
Low Profile
01-018-334
AKW Limited
Pointon Way, Hampton Lovett,
Droitwich Spa, WR9 0LR
United Kingdom
www.akw-ltd.co.uk
DoP 01-018-330-02
DoP
07-003-050-02
Braddan Shower Tray
Installation And User Care Instructions
Read ALL instructions carefully BEFORE installation and leave with the end user
Available Sizes (mm)
Sizes Avaliable
800x800
1000x1000
1200x900
1500x700
Installation
IMPORTANT
Before completing the installation, water test the flow from tray into waste for correct installation and drainage efficiency.
It is important to ensure that the floor is level in all directions before putting the tray into place. If water puddles away from
the waste, this is a clear indication that the levels are not correct - the water is acting as a 'spirit level'.
The sides on the tray A and B may well show level on testing, but if point C is low, then water will puddle in the area of point C
and the only remedy is to level the floor and refit the tray. The tray has 'lands' on all four sides.
Use a spirit level front to back and side to side - all 'lands' must be level (ABC) - the fall is moulded into the tray (See Fig. A).
It is not necessary to remove plaster from the walls for installing the above trays. When tiling, ensure that the bottom row of
tiles are bedded in to align with the final position of the tray.
For latest AKW news and
products, scan this code
with your phone or tab
device.
Usercare Instructions
The Braddan Shower Tray should be cleaned periodically to remove any accumulation of hair or other waste material, using
normal domestic bathroom cleaning materials. Do not use strong or concentrated acidic, alkaline or other cleaning materials as
these may damage or discolour the product. After cleaning always flush down with water then wipe thoroughly with a damp
cloth to remove any cleaning material residues before drying off.
01-018-200-09
3mm
Guaranteed
for
4mm
Life
5mm
820x820
900x900
1200x650
1200x700
1300x700
1300x820
1500x820
1700x700
A
C
Fig. A
UK
UK
1000x700
1000x800
1200x760
1200x820
1420x700
1420x820
1800x700
1800x820
B
Technical Help line
01905 560219