Air Hogs Micro Havoc Heli Manual - Página 4

Procurar online ou descarregar pdf Manual para Brinquedo Air Hogs Micro Havoc Heli. Air Hogs Micro Havoc Heli 4 páginas.

Imprimir página

HOW TO FIX YOUR TWIN ROTORS

If the linkage between your twin rotors comes undone and is dangling below the bottom rotor,

it is very EASY to fix! (A)

Carefully re-attach the linkage back onto the top connector and gently push it into place. (B)

While your there, you might want to check around the area for any fibers or debris that might

affect your flight performance. Carefully remove it with tweezers and you are ready to start

flying again!

PROBLEM

Main rotor won't move.

Tail rotor is broken or not moving.

Suddenly stops and drops while flying.

The Helicopter is not reacting to the

controller.

Helicopter is losing control.

Helicopter is not holding a charge.

Helicopter will not lift off the ground.

Helicopter only turns in one direction.

For further questions and problems, please visit our website www.airhogs.com.

Safety Precautions:

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

- Keep hands, hair and loose clothing away from the propeller when power switch is turned ON.

- Turn off controller/charger and helicopter when not in use

- Remove battery from controller/charger when not in use.

- Parental guidance is recommended for the flight.

- Keep your helicopter in your sight so that you can supervise it all the time.

FCC Statements

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received, including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

Care and Maintenance:

- Always remove batteries from the toy when it is not being used for a long period of time.

(controller/charger only)

- Wipe the toy gently with a clean damp cloth.

- Keep the toy away from direct heat.

- Do not submerge the toy into water that can damage the electronic assemblies.

Battery Cautions:

- Non-rechargeable batteries are not to be recharged

- Rechargeable batteries are to be removed from the toy before being charged

(controller/charger only).

- Rechargeable batteries are only to be charged by an adult

- Different types of batteries or new and used batteries are not to be mixed (controller/charger only).

- Only batteries of the same or equivalent type as recommended are to be used.

- Batteries are to be inserted with correct polarity.

- Exhausted batteries are to be removed from the toy (controller/charger only).

- The supply terminals are not to be short-circuited.

Helicopter is equipped with a Li-Poly rechargeable battery,

please also pay attention to the following cautions for safety use:

- Do not dispose the battery in fire or heat.

- Do not use or leave the battery near a heat source such as fire or heater.

- Do not strike or throw the battery against hard surface.

- Do not immerse the battery in water, and keep the battery in a cool dry environment.

- When recharging, only use the battery charger specifically for that purpose.

- Do not over-discharge the battery.

- Do not connect the battery to an electrical outlet.

- Do not directly solder the battery and pierce the battery with a nail or other sharp object.

- Do not transport or store the battery together with metal objects such as necklaces, hairpins etc.

- Do not disassemble or alter the battery.

- Charge the battery every 6 months.

- Turn off your equipment power switch after use.

- As for a used battery, please recycle after covering the battery terminals with insulation tape or inserting it

to an individual poly-bag.

Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada

Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221, USA

Spin Master Toys Far East Limited. Rm #1113, 11/F, Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HK

Spin Master Toys UK Ltd., Meadowbank, Furlong Road, Bourne End, Bucks, SL8 5AJ, United Kingdom

Spin Master France – 36 rue de Silly – 92100 Boulogne Billancourt – France

North American Consumer Information

Phone: 1-800-622-8339

www.spinmaster.com

TROUBLESHOOTING

CAUSE

ON/OFF switch is set to OFF.

Weak battery.

Something may be caught in the rotor.

Rotor may have chipped during flight.

Try stearing left/right to activate tail rotor.

Weak power.

Helicopter may be out of range from controller.

A,B,C channel selection on controller is not

correct.

Helicopter may not be turned ON.

May be another infrared (IR) device using the

same channel.

Bright lights may be affecting the IR control.

You may be too far away from the controller.

Helicopter might be turned ON while charging.

Controller/charger is low on battery power.

Helicopter may not be fully charged.

Helicopter is not trimmed correctly.

Set switch to ON.

Re-charge the helicopter using the charging port OR check

batteries in the controller.

Remove blockage.

Replace tail rotor with the spare set in the package.

Re-charge helicopter or check battery power in controller.

Double check the letter on the bottom of the helicopter and

adjust the channel selector on the controller.

Turn helicopter ON.

Avoid these if possible, or choose another place to operate

the helicopter.

Turn down lights or change flight environment.

Stay closer to the helicopter with the controller.

Turn OFF the helicopter so that it is not flashing.

Replace batteries in the controller.

Charge helicopter fully, until green light turns off.

Refer to the TRIMMING section in the instruction sheet.

- New and alkaline batteries are recommended for use in controller/charger to obtain best and maximum performance.

- You are advised to replace with new batteries as soon as the function becomes impaired.

- Users should keep and retain this information for future reference.

- Users should keep strict accordance with the instruction manual while operation the product.

- Your controller/charger is tailor-made for the Li-Poly rechargeable battery used in Micro Havoc Heli™.

Do not use it to charge any battery other than that in the helicopter.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Note:

- Parental guidance is recommended when installing or replacing batteries.

- Under the environment with electrostatic discharge, the sample may malfunction and

require user to reset the sample.

Special Note to Adults:

- Regularly examine for damage to the plug, enclosure and other parts. In the event of

any damage, the toy must not be used with the controller/charger charger until the

damage has been repaired.

- This toy is not intended for children under 3 years old.

- This toy must only be used with the recommended charger

- Do not try to charge other batteries with controller/charger.

Battery requirement for Micro Havoc Heli™:

Power Supply :

Rating

: DC 3.7 V, 1,8 W

Batteries

: 1 x 3.7 V Li-Poly Rechargeable Battery Pack

Requires 1 x 3.7 V Li-Poly Rechargeable Battery Pack (included)

Battery requirement for Controller/charger:

Power Supply :

Rating

: DC 6 V, 1,2 W

Batteries

: 4 x 1.5 V "AA"/LR6/AM3

Requires 4 x 1.5 V "AA" size batteries (not included)

Conforms to product safety standards ASTM F963,

EN71 regulatory requirements. Products and colors may vary.

Please retain this information for future reference. Patent Pending.

MADE IN CHINA.

#44307

NEN

REV 1

WRONG

SOLUTION

RIGHT