AmpliVox SW800 Manual do utilizador - Página 6

Procurar online ou descarregar pdf Manual do utilizador para Sistema de altifalantes AmpliVox SW800. AmpliVox SW800 12 páginas. Battery powered pa system
Também para AmpliVox SW800: Manual do utilizador (10 páginas), Manual do utilizador (8 páginas), Manual do utilizador (8 páginas), Manual do utilizador (10 páginas)

Imprimir página

16 CHANNEL UHF WIRELESS

WIRELESS RECEIVER PANEL

•

Channel Display (A)

•

RF - Radio Frequency Indicator (B)

•

AF - Audio Frequency Indicator (C)

•

ASC / IR Auto Channel Select (Handheld Only) (D)

•

Select Buttons - Manual Channel Selection (E)

•

Mute Level Adjustment (F)

•

Volume Control (G)

RECEIVER / TRANSMITTER SETUP:

•

The receiver has its own POWER / VOLUME Control (G). First make sure that

you have screwed on the UHF antenna. Turn Power On. A

Frequency Channel will appear in the Channel Display (A). Press Select But-

tons (E) to select a channel. Channel number must match channel number on

wireless transmitter.

•

The transmitter bodypack is operated by 1 - "AA" 1.5 Volt alkaline battery.

Slide off battery cover (H) and install battery as shown. Make certain the bat-

tery is fully seated in its compartment so the cover slides in place easily. Bat-

tery life with alkaline batteries is approximately 8 hours of operating time.

•

Select a channel (1-16) on side panel (I) using the supplied screw driver to

select channel number. Channel selected should match channel on receiver.

When transmitter and receiver are set to correct channel the RF indicator (B)

will glow red when transmitter is turned on.

•

Plug the Lapel / Headset microphone into the Mic Input Jack (K). The micro-

phone can be clipped to a necktie or other clothing, using the supplied clip.

The lapel mic should be placed under the chin, as close to the center of the

body as possible.

•

Slide the power ON / MUTE / OFF switch (J) to the ON position (the LED indi-

cator light will illuminate green). Replace batteries when this LED turns red.

• MUTE LEVEL (F) is set to lowest threshold (fully counter-clockwise)

when it leaves the factory. If speaker sound is experiencing loud white

noise interference bursts due to environmental interference, and no oth-

er clear channel is available, slowly turn the MUTE level (F) clockwise with

small screwdriver until white noise sound is muted. This operation is done with

all wireless microphones and bodypack transmitters turned off until MUTE

level adjustment is complete. This also effects transmitter distance.

• GAIN SWITCH (L): If you are a soft spoken person then set the switch to the

10 dB position. If you are a loud speaking person then set the switch to the -

10 dB position. Adjust to prevent distortion while speaking.

WIRELESS HANDHELD MICROPHONE—MODEL S1695

If you are using the AmpliVox S1695 Wireless Handheld Microphone Transmitter, screw off the lower bottom section of microphone

and insert 2 - "AA" 1.5 Volt alkaline batteries.

IMPORTANT: Because the microphone has an AUTO SYNC function, you first select channel you wish to use on the receiver.

Then press the ASC button (D), the IR light will start to flash. Turn on microphone and point end (6) of microphone at the flashing

IR light on receiver and the microphone will auto sync to the same channel as selected on the receiver.

BATTERIES

1. Hold the body of microphone in hand and twist off bottom sec-

tion of microphone.

2. Insert two "AA" batteries.

3. Twist bottom section back on to microphone.

BATTERY STATUS

The life expectancy of the two batteries is about 10 hours. When the

"BATTERY" symbol on the display screen keeps flashing the batter-

ies should be replaced immediately.

Wireless Transmitter - Bodypack

Battery Cover

Channel Selector

Top Panel