AMSOIL BMK-22 Manual de instruções de instalação e manutenção - Página 6

Procurar online ou descarregar pdf Manual de instruções de instalação e manutenção para Racks & Stands AMSOIL BMK-22. AMSOIL BMK-22 6 páginas. Dual-gard by-pass filter mounting kit

Imprimir página

Diagram E

1 1 . . P P r r o o v v i i d d e e f f o o r r l l e e n n g g t t h h c c h h a a n n g g e e

WRONG

RIGHT

In straight hose installations allow enough slack in

the hose line to provide for changes in length that will

occur when pressure is applied. This change in length

can be from +2% to -4%.

4 4 . . A A v v o o i i d d m m e e c c h h a a n n i i c c a a l l s s t t r r a a i i n n s s

WRONG

Use elbows and adapters in the installation to relieve

strain on the assembly, and to provide easier and

neater installations that are accessible for inspection and

maintenance.

7 7 . . S S e e c c u u r r e e f f o o r r p p r r o o t t e e c c t t i i o o n n

WRONG

Install hose runs to avoid rubbing or abrasion. Use clamps to support long runs

of hose or to keep hose away from moving parts. It is important that the clamps

do not allow the hose to move. This movement will cause abrasion and pre-

mature hose failure.

Return-Line

Swivel Fitting

Oil filler cap

Drill

⁄

hole

A A M M S S O O I I L L I I N N C C . . , , AMSOIL Bldg., Superior, WI (715) 392-7101

2 2 . . A A v v o o i i d d t t w w i i s s t t i i n n g g a a n n d d o o r r i i e e n n t t p p r r o o p p e e r r l l y y

WRONG

Do not twist hose during installation. This can be deter-

mined by the printed layline on the hose. Pressure

applied to a twisted hose can cause hose failure or

loosening of connections.

5 5 . . U U s s e e p p r r o o p p e e r r b b e e n n d d r r a a d d i i u u s s

RIGHT

WRONG

Keep the bend radius of the hose as large as possible

to avoid collapsing of the hose and restriction of ﬂow.

Follow catalog specs on minimum bend radii.

RIGHT

B B Y Y - - P P A A S S S S O O I I L L F F I I L L T T E E R R R R E E T T U U R R N N - - L L I I N N E E F F I I T T T T I I N N G G : :

A swivel fitting can be installed directly on

your oil ﬁlter cap for the oil return-line from the

AMSOIL By-Pass Filter. This fitting can be

used (in most cases) instead of the self-tapping

hollow bolt, which is usually installed on the

oil pan.

The Return-Line Fitting is made of a sturdy

brass-alloy and is constructed so that the top

of the ﬁxture can swivel. This makes it easy to

take off your oil cap. The installation of the ﬁt-

ting is simple and generally takes 5-10 min-

utes. Order BP-89. Be sure there is not a

crankcase vent in this area.

RIGHT

8 8 . . A A v v o o i i d d I I m m p p r r o o p p e e r r H H o o s s e e M M o o v v e e m m e e n n t t

WRONG

Make sure relative motion of the machine components produces bending rather than twist-

ing of the hose. Hose should be routed so that the ﬂex is in the same plane as the equipment

movement.

3 3 . . P P r r o o t t e e c c t t f f r r o o m m h h a a z z a a r r d d o o u u s s e e n n v v i i r r o o n n m m e e n n t t

WRONG

RIGHT

Keep hose away from hot parts. High ambient temper-

atures will shorten hose life. If you can not route it

away from the heat source, insulate it.

6 6 . . U U s s e e p p r r o o p p e e r r b b e e n n d d r r a a d d i i u u s s ( ( c c o o n n t t . . ) )

3.00

RADIUS

6.00

DIAMETER

Maximum bend radius is measured on the inside bend

of the hose. To determine minimum bend, divide the

total distance between ends (B length) by 2. For exam-

ple 8 = 6, minimum bend radius = 3.

RIGHT

I I N N S S T T A A L L L L I I N N G G A A N N O O I I L L S S A A M M P P L L I I N N G G P P E E T T C C O O C C K K

O O N N T T H H E E S S P P I I N N - - O O N N B B Y Y - - P P A A S S S S : :

Getting a clean and uncontaminated oil

sample is easy and simple when an oil

sampling pet-cock is installed into the

Spin-On By-Pass Oil Filter system. This

can be easily done by ordering a BK-13.

BP-274

1/08