AMSOIL BMK-27 Instruções de instalação e manutenção - Página 2

Procurar online ou descarregar pdf Instruções de instalação e manutenção para Equipamento de serviço AMSOIL BMK-27. AMSOIL BMK-27 6 páginas. Dual remote filtration system mounting kit (duramax)

Imprimir página
AMSOIL BMK-27 Instruções de instalação e manutenção
7. Use plastic ties (BP-46) to secure hose in position and away from potential damage. Trim ties with
side cutter. Note: Over tightening the plastic ties may cause the hose to collapse and restrict oil flow.
8. Fill the selected Full-flow and By-pass filters with the same motor oil being used in the vehicle. Lubricate
the filter gaskets with oil and spin filters onto mount. Tighten per instructions on the filter can.
E. Start up procedures
1. Check that all fittings and hoses are securely attached, and that the hoses are routed properly.
2. Check engine oil level. Fill to full mark if necessary.
3. With the equipment secured start the engine and immediately check oil pressure. Note: Pressure
may initially take a moment or two to rise. Installing the Dual Remote By-Pass System may
result in a slight vibration sound in some applications. No harm to the engine will occur. Please
contact AMSOIL Technical Services for more information.
Caution: Carefully check for leaks at fittings, hoses and mount. If leaks are observed, STOP
ENGINE IMMEDIATELY, repair leaks and continue.
4. After engine has warmed, shut off and re-check engine oil level. Top off as necessary.
5. Record equipment/operating hours and date of installation.
F. Periodic maintenance
1. Periodic visual inspection of the fittings and hoses is recommended. Check for leaks, hose
deterioration and cuts. Repair and/or replace as necessary.
2. Refer to Recommended Filter Change Interval chart for servicing intervals.
3. To change the filter elements:
a. Ensure engine is off and use caution as the engine, oil and filter may be hot and could result
in an injury.
b. Using a filter wrench, remove the filter elements. Dispose of properly.
c. Clean the filter gasket contact areas on the mount with a clean, lint-free rag.
d. Lubricate the new filter gaskets with clean oil or grease.
e. Fill filters as full as possible with engine oil.
f. Screw on new filters, tighten per instructions on the filter can.
g. Start engine and check for leaks.
h. Check engine oil level, fill as needed.
4. Record equipment/operating hours for future reference.
Full-Flow
Filter
Diagram A
MINIMUM AREA NEEDED FOR
DUAL MOUNT AND SPIN-ON OIL FILTER ELEMENTS
* Mount and element heights plus 1-inch removal clearance
Diagram C
Minimum Bend Radius
By-Pass
Filter
1
2
⁄
(1.5)
4
1
⁄
I.D. Hose BP-350
2
Dual Mount By-pass Filter System (BMK-27) for GM Duramax
Item
Description
1.
Filter Mount Assembly
2.
Allen Head Plug
1
3.
1
4.
1
5.
6.
90 degree fitting
7.
"O" ring fitting
8.
Hose Fitting
1
9.
10.
Spin-On Adapter
11.
Adapter Retaining Nut
12.
Gasket 3.11 ID
13.
Mounting Bracket Top
14.
Mounting Bracket Bottom
1
15.
1
16.
17.
Adapter Nut O-ring
Full-Flow Filter
By-Pass Filter
Plastic Tie
Thread Sealant
Instruction Sheet
Optional Parts
Oil Sampling Kit
Deluxe oil sampling valve
(Must also order fitting BP209)
90 degree fitting
45 degree fitting
Mounting Angle Diagram B
(Recommendations are the same right to left and front to back)
Mounting angle above horizontal is not recommended
180°
ACCEPTABLE
160°
GOOD
ANGLE
130°

Mounting Template

Parts and assembly list
⁄
20 x 1 Hex Head Bolt
4
⁄
I.D. Washer
4
⁄
Self Locking Nuts
4
7
5
⁄
-14 x
⁄
JIC
8
8
7
5
⁄
-14 x
⁄
JIC
8
8
⁄
I.D. hose
2
13
⁄
-16
16
1
⁄
-20 x 1
⁄
Hex Head Bolt
4
2
⁄
ID Fender Washer
4
1
⁄
NPT
4
7
5
⁄
-14 x
⁄
JIC
8
8
7
5
⁄
-14 x
⁄
JIC
8
8
PREFERRED MOUNTING ANGLE
1
⁄
(.25)
4
1
2
⁄
4
(2.25)
Qty.
Part No.
1
BK-309
2
BP-191
4
BP-23
6
BP-21
8
BP-22
1
BP-331
3
BP-289
4
BP-360
12
BP-350
1
BP-420
1
BP-405
1
BP-220
1
BP-194
1
BP-195
4
BP-185
4
BP-186
1
BP-346
1
EaO-26
1
EaBP-100
2
BP-46
1
BP-198
1
BP-258
1
BK-13
1
G1570
1
BK-21
1
BK-22
HORIZONTAL
0°
ACCEPTABLE
20°
GOOD
ANGLE
50°
5
1
⁄
16
(1.3125)