Aleph QT-40BSL Manual - Página 2

Procurar online ou descarregar pdf Manual para Sensores de segurança Aleph QT-40BSL. Aleph QT-40BSL 2 páginas. Quad-tech intrusion detectors

Top View
0
1.5
3.0
4.5
6.0
7.5
9.0
10.5 12.0
28
25
20
15
10
5
0
5
10
15
20
25
28
0
5
10
15
20
25
30
35
ft
Note: Dashed line indicates typical microwave coverage.
Troubleshooting
T r oub le
Unit does not power up.
Alarm LED does not light
.
Alarm LED / Relay triggers without
movement in detection area .
LED indicates Alarm, no alarm output
.
Alarm LED on constantly, no fault in
protected area or wiring .
Unit continues to operate after the
input power has been disconnected.
Maintenance
• INSPECTION: An inspection of this unit should be made periodically, consisting of, but not limited to all mounting, wiring, and the
condition of the interior area and components.
• CLEANING: Clean the plastic parts of this unit with a soft, clean, cloth dampened with water.
• TESTING:
This unit should be tested routinely for proper operation. At a minimum, operation should be fully checked yearly.
Specifications
Microwave Freq.
Input Voltage
Input Current
15 mA max. (SL model 30 mA), 9 mA quiescent (approx.)
Pyro Type
Pulse Count
Warm-up Time
Alarm Period
Visual Indicator
Alarm Output
NC, solid state, 19 VDC, 100 mA, 13 ohms resistance typ.
Tamper Output
Mounting Height
Operating Temp.
Environmental
Weight
Dimensions
P/N 9-900-003-01 Rev.
Detection Pattern
m
8.5
Main Lens: 40WASTD Wide Angle
7.5
6.0
4.5
0
3.0
8.0
1.5
0
1.5
3.0
4.5
0
6.0
0
ft
7.5
8.5
Lookdown
40
C a use
No or low input power.
Input power polarity reversed .
.
LED jumper is set to "
L
E
D
OFF"
Incorrect sensor mounting height .
Pulse Count setting incorrect for
secured area .
Unsecured environment : Animals /
rodents in detection area .
Heater /a ir conditioning equipment in
sensor view.
Direct sun or headlights in sensor
view.
Incorrect wiring at alarm output
terminals.
.
Lightning damage
D
e
e f
i t c
e v
U
n
t i
.
The wire to the "-" power input was
disconnected, the "+" is still connected.
The power is finding a return path
through the Alarm Output protection
device and alarm wiring.
10.525 GHz, pulsed
10 to 16 VDC, 12 VDC nominal
Dual Element
Jumper selectable: PC1, PC2
< 50 seconds
2.4 seconds, retriggerable
Red Alarm LED (Selectable On / Off)
NC, dry contact, 30 VDC, 500 mA, 5 W max.
7 to 8.5 ft (2.1 to 2.6 m)
14° to 131° F (-10° to 55° C)
95% humidity non-condensing
3.7 oz / 105 g
4.8" H x 2.5" W x 1.7" D / 12.2cm x 6.4cm x 4.3cm
© 2009 Aleph America Corporation
Side View
1.5
3.0
4.5
5
10
15
Mid Range
R e m e d y
Apply proper input voltage.
Correct wiring polarity.
Set LED jumper to "
L
E
D
EN
AB
L
E
D
"
.
Increase / decrease mounting height .
Set pulse count jumper to suit the
.
required detection characteristics
Block access of animals/rodents.
.
Re-aim sensor
Add curtain / shade to block light
sources.
Correct wiring fault .
Replace sensor.
R
e
p
a l
c
e
s
e
n
s
o
. r
Disconnect wire from the "+" power
input.
All rights reserved
6.0
7.5
9.0
20
25
30
Automatic LED Brightness
The QT Series alarm LED indicator includes an automatic
brightness function. In order to allow for a less noticeable
installation, LED brightness is reduced as ambient room light
level drops.
The LED can be fully disabled by removing the ALARM LED
jumper.
FCC/IC Information:
FCC ID: DNHQT-001-00
IC: QT00100-xxxx
FCC/IC Statement:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 and ICES-003 of the FCC and
Industry Canada Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
The user should not modify or change this equipment without written
approval from ALEPH.
Modification could void authority to use this equipment.
Note:
• This detector is designed to be incorporated into an alarm system.
As it is part of a system, ALEPH cannot assume responsibility for
theft or damage if the system fails to operate.
Contact Aleph
Nippon Aleph Corporation
-Security Products Headquarters-
1-28-52, Komaoka, Tsurimi-ku
Yokohama-shi, Kanagawa-ken
JAPAN, 230-0071
Tel: +81 045-575-4290 / Fax: +81 045-580-1676
WEB: http://www.nippon-aleph.co.jp
Aleph America Corporation
4700 Aircenter Cir, Reno, NV, 89502
USA
Tel: 775 827 8000 / Fax: 775 827 8044
WEB: http://www.aleph-usa.com
Aleph Europe Ltd.
1 Newton Close, Park Farm Industrial Estate
Wellingborough, Northamptonshire, NN8 6UW
England
Tel: 044 193 367 9600 / Fax: 044 193 340 1165
WEB: http://www.alepheurope.com
m
12.0
10.5
Long
Range
0
35
40